Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0751    Shift Solenoid "A" Performance (Shift Solenoid Valve S1)

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd or 4th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC No.
DTC Detection Conditions
Trouble Areas
P0751
S1 stuck ON malfunction*1:
The ECM determines that there is a malfunction when the following conditions are met:
(a) When the ECM directs the gearshift to switch to 4th gear, the engine overruns (clutch slips).
(b) When the ECM directs the gearshift to switch to 4th gear, the actual gear is shifted to 1st.
  1. Shift solenoid valve S1 is stuck open
  2. Valve body is blocked
  3. Shift solenoid valve S1
  4. Automatic transmission (clutch, brake or gear, etc.)
P0751
S1 stuck OFF malfunction*2:
The ECM determines that there is a malfunction when the following conditions are met:
(a) When the ECM directs the gearshift to switch to 1st gear, the actual gear is shifted to 4th.
(b) When the ECM directs the gearshift to switch to 4th gear, the actual gear is also shifted to 4th.
  1. Shift solenoid valve S1 is stuck closed
  2. Valve body is blocked
  3. Shift solenoid valve S1
  4. Automatic transmission (clutch, brake or gear, etc.)

HINT:
  1. Gear positions in the event of a solenoid valve mechanical problem:

    Gearshift controlled by ECM
    1st
    2nd
    3rd
    4th
    *1: Actual gear position under S1 stuck ON malfunction
    1st
    2nd
    2nd
    1st
    *2: Actual gear position under S1 stuck OFF malfunction
    4th
    3rd
    3rd
    4th


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S1.
The ECM controls the gearshifts by turning the shift solenoid valves "ON/OFF". When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0751:
Shift solenoid valve S1/OFF malfunction
Shift solenoid valve S1/ON malfunction
Required sensors/Components
Shift solenoid valve S1, Speed sensor (SP2), Speed sensor (NCO), Crankshaft position sensor (NE), Throttle position sensor, MAF
Frequency of operation
Continuous
Duration
OFF malfunction (A):
1.0 second
OFF malfunction (B):
0.4 seconds
ON malfunction (A):
0.8 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The following conditions are common to all OFF malfunctions (A), (B) and ON malfunctions (A), (B). 
The monitor will run whenever the following DTCs are not present.
P0115 - P0118 (ECT sensor)
P0125 (Insufficient ECT for closed loop)
P0500 (VSS)
P0748 - P0798 (Trans solenoid (range))
Shift solenoid "A" (S1) circuit
Shift solenoid "B" (S2) circuit
ECT (Engine Coolant Temperature) sensor circuit
Input speed sensor (NCO) circuit
Output speed sensor (SP2) circuit
There is no malfunction in the sensor circuits shown on the left
Transmission shift position
"D"
ECT (Engine Coolant Temperature)
40°C (104°F) or more
Spark advance from max. retard timing by knock control
0° CA or more
Engine
Running

OFF malfunction (A) 
ECM selected gear
1st
Vehicle speed
6.2 mph (10 km/h) or more
and
Less than 24.8 mph (40 km/h)
Throttle valve opening angle
15 % or more and
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

OFF malfunction (B) 
Current ECM selected gear
4th
Last ECM selected gear
3rd
Actual gear when ECM selected 3th gear
3rd

ON malfunction (A) 
ECM selected gear
4th
Vehicle speed at current ECM selected gear
- Vehicle speed at last ECM selected gear
Less than 6.2 mph (10 km/h)
Throttle valve opening angle at current ECM selected gear
- Throttle valve opening angle at last ECM selected gear
Less than 10 %
Throttle valve opening angle
Less than 20 %
Vehicle speed
Less than 52.8 mph (85 km/h)

ON malfunction (B) 
Current ECM selected gear
4th
Last ECM selected gear
3rd

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. Both of the following conditions are met: OFF malfunctions (A) and (B)
    2 detections are necessary in 1 driving cycle.
    1st detection: Temporary flag ON
    2nd detection: Pending fault code ON

OFF malfunctions (A) and (B) 
Input speed/Output speed (NC0/SP2)
0.00 or more and 0.22 or less
(This means actual gear is 4th)
[ON malfunction]
  1. Both of the following conditions are met: ON malfunctions (A) and (B)

ON malfunction (A) 
NE current - NE last
NE current: Engine speed at current ECM selected gear
NE last: Engine speed at last ECM selected gear
950 rpm or more

ON malfunction (B) 
Input speed/Output speed (NC0/SP2)
Not change as follows
0.93 or more and 1.07 or less
(This means actual gear is 3rd)
↓
0.00 or more and 0.22 or less
(This means actual gear is 4th)

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one method of shortening labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Push the "ON" button of the tester.

  6. Select the items "DIAGNOSIS/ ENHANCED OBD II/ ACTIVE TEST/ SHIFT".

  7. According to the display on the tester, perform the "ACTIVE TEST".

    HINT:
    While driving, the shift position can be changed with the intelligent tester.
    Comparing the shift position directed by the ACTIVE TEST with the actual shift position enables you to confirm the problem (Click here).


    Item
    Test Details
    Diagnostic Note
    SHIFT
    [Test Details]
    Operate the shift solenoid valve and set each shift position by manually.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 31 mph (50 km/h)
    [Others]
    1. Press → button: Shift up
    2. Press ← button: Shift down
    Possible to check the operation of the shift solenoid valves.

    HINT:
    1. This test can be conducted when the vehicle speed is 31 mph (50 km/h) or less.
    2. The 3rd to 4th up-shifting must be performed with the accelerator pedal released.
    3. The 4th to 3rd down-shifting must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position directed by the ECM is shown in the DATA LIST/ SHIFT display on the intelligent tester.
    6. The shift solenoid valve S1 is turned on/off normally when the shift lever is in the D position:

      Gearshift controlled by ECM
      1st
      2nd
      3rd
      4th
      Shift solenoid valve S1
      ON
      ON
      OFF
      OFF

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0751)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select the items "DIAGNOSIS/ ENHANCED OBD II/ DTC INFO/ CURRENT CODES".

  1. Read the DTCs using the intelligent tester.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0751" is output
    A
    "P0751" and other DTCs
    B

    HINT:
    If any codes besides "P0751" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT SHIFT SOLENOID VALVE S1
G022784E02
  1. Remove the shift solenoid valve S1.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S1) - Solenoid
    Body (S1)
    11 to 15 Ω at 20°C (68°F)

  1. Connect positive (+) lead to the terminal of the solenoid connector, negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE S1
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY