Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1800/51    Short in Driver Side Squib Circuit

DTC    B1801/51    Open in Driver Side Squib Circuit

DTC    B1802/51    Short to GND in Driver Side Squib Circuit

DTC    B1803/51    Short to B+ in Driver Side Squib Circuit

for Preparation Click here


DESCRIPTION

  1. The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
  2. The circuit signals the SRS to deploy when deployment conditions are met.
  3. These DTCs are set when a malfunction is detected in the driver side squib circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1800/51
  1. The center airbag sensor assembly receives a line short circuit signal in the driver side squib circuit for 2 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1801/51
  1. The center airbag sensor assembly receives a line short circuit signal in the driver side squib circuit for 2 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1802/51
  1. The center airbag sensor assembly receives a line short circuit to ground signal in the driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1803/51
  1. The center airbag sensor assembly receives a line short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM


H101822E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. If using the intelligent tester (read the 5-digit DTCs):
      Using the intelligent tester, check for DTCs (Click here).

      Result:

      Result
      Proceed to
      DTC B1800 is output.
      A
      DTC B1801 is output.
      B
      DTC B1802 is output.
      C
      DTC B1803 is output.
      D

    2. If not using the intelligent tester (read the 2-digit DTCs):
      Check for DTCs (Click here).

      Result:

      Result
      Proceed to
      DTC 51 is output.
      E



B
Go to step 7

C
Go to step 11

D
Go to step 15

E
Go to step 21
A


2.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


3.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the spiral cable.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


4.CHECK SPIRAL CABLE (FOR SHORT)


    H100857E04
  1. Disconnect the spiral cable connectors from the instrument panel wire and steering pad.

  1. Release the activation prevention mechanism built into connector D (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D+ - D-
    Always
    1 MΩ or Higher



NG
REPLACE SPIRAL CABLE
OK


5.CHECK INSTRUMENT PANEL WIRE (FOR SHORT)


    H100856E06
  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - A26-2 (D-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101859E01
  1. Connect the instrument panel wire connectors to the center airbag sensor assembly and spiral cable.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800 is not output.

HINT:
DTCs other than B1800 may be output at this time, but they are not related to this check.



OK
Go to step 20
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

7.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


8.CHECK CONNECTION OF CONNECTORS
  1. Check that the spiral cable connectors (on the steering pad side) are properly connected.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


9.CHECK SPIRAL CABLE (FOR OPEN)


    H100857E04
  1. Disconnect the spiral cable connectors from the instrument panel wire and steering pad.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D+ - D-
    Always
    Below 1 Ω



NG
REPLACE SPIRAL CABLE
OK


10.CHECK INSTRUMENT PANEL WIRE (FOR OPEN)


    H100856E07
  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - A26-2 (D-)
    Always
    Below 1 Ω



OK
Go to step 19
NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

11.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


12.CHECK CONNECTION OF CONNECTORS
  1. Check that the spiral cable connectors (on the steering pad side) are properly connected.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


13.CHECK SPIRAL CABLE (TO GROUND)


    H100857E04
  1. Disconnect the spiral cable connectors from the instrument panel wire and steering pad.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D+ - Body ground
    Always
    1 MΩ or Higher
    D- - Body ground
    Always
    1 MΩ or Higher



NG
REPLACE SPIRAL CABLE
OK


14.CHECK INSTRUMENT PANEL WIRE (TO GROUND)


    H100856E07
  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - Body ground
    Always
    1 MΩ or Higher
    A26-2 (D-) - Body ground
    Always
    1 MΩ or Higher



OK
Go to step 19
NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

15.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


16.CHECK CONNECTION OF CONNECTORS
  1. Check that the spiral cable connectors (on the steering pad side) are properly connected.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


17.CHECK SPIRAL CABLE (TO B+)


    H100857E04
  1. Disconnect the spiral cable connectors from the instrument panel wire and steering pad.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D+ - Body ground
    Ignition switch ON
    Below 1 V
    D- - Body ground
    Ignition switch ON
    Below 1 V



NG
REPLACE SPIRAL CABLE
OK


18.CHECK INSTRUMENT PANEL WIRE (TO B+)


    H100856E07
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - Body ground
    Ignition switch ON
    Below 1 V
    A26-2 (D-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


19.CHECK CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 18, begin from (a). If continuing from any other step, begin from (c).



    H101860E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the instrument panel wire connectors to the center airbag sensor assembly.

  1. Using a service wire, connect D+ and D- of connector E.

NOTICE:
  1. Twist the end of the service wire in order to insert it into the connector.
  2. Do not forcibly insert the twisted service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTCs B1801, B1802 and B1803 are not output.

HINT:
DTCs other than B1801, B1802 or B1803 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


20.REPLACE STEERING PAD (DRIVE SIDE SQUIB)

HINT:
If continuing from step 19, begin from (c). If continuing from any other step, being from (a).



    H101861E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector E.

  1. Connect the connectors to the steering pad.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTCs B1800, B1801, B1802 and B1803 are not output.

HINT:
DTCs other than B1800, B1801, B1802 or B1803 may be output at this time, but they are not related to this check.



NG
REPLACE STEERING PAD
OK

OTHERS USE SIMULATION METHOD TO CHECK 

21.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


22.CHECK CONNECTORS
  1. Check that the spiral cable connectors (on the steering pad side) are properly connected.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


23.CHECK SPIRAL CABLE


    H100857E04
  1. Disconnect the spiral cable connectors from the instrument panel wire and steering pad.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D+ - Body ground
    Ignition switch ON
    Below 1 V
    D- - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D+ - D-
    Always
    Below 1 Ω
    D+ - Body ground
    Always
    1 MΩ or Higher
    D- - Body ground
    Always
    1 MΩ or Higher

  1. Release the activation prevention mechanism built into connector D (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D+ - D-
    Always
    1 MΩ or Higher



NG
REPLACE SPIRAL CABLE
OK


24.CHECK INSTRUMENT PANEL WIRE


    H100856E06
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - Body ground
    Ignition switch ON
    Below 1 V
    A26-2 (D-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - A26-2 (D-)
    Always
    Below 1 Ω
    A26-1 (D+) - Body ground
    Always
    1 MΩ or Higher
    A26-2 (D-) - Body ground
    Always
    1 MΩ or Higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-1 (D+) - A26-2 (D-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


25.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H100855E03
  1. Replace the steering pad (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the instrument panel wire to the airbag sensor assembly center and spiral cable.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 51 is not output.

HINT:
DTCs other than 51 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END