Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C1241/41    Low Battery Positive Voltage

for Preparation Click here


DESCRIPTION

If there is a problem with the brake actuator (skid control ECU) power supply circuit, the skid control ECU outputs a DTC and prohibits operation under the fail safe function.
If the voltage supplied to the IG1 terminal is not within the DTC detection threshold due to malfunctions in parts such as the battery or alternator circuit, this DTC is stored.

DTC No.
DTC Detecting Conditions
Trouble Areas
C1241/41
  1. At vehicle speed of 2 mph (3 km/h) or more, voltage at IG1 terminal remains at 9.5 V or less for 10 seconds or more.
  2. When solenoid relay ON, voltage at IG1 terminal 0.5 V or less, and contact of relay OFF for 0.2 seconds or more.
  3. When voltage at IG1 terminal 9.5 V or less, voltage of speed sensor power supply decreases for 60 seconds or more.
  1. Battery
  2. Charging system
  3. Power source circuit

WIRING DIAGRAM


C124743E01


INSPECTION PROCEDURE

1.INSPECT BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM
OK


2.INSPECT FUSE (IG1 NO. 2)


    F051661E03
  1. Remove the IG1 NO . 2 fuse from the driver side J/B.

  1. Measure the resistance of the IG1 NO. 2 fuse.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the IG1 NO. 2 fuse.



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3.INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (IG1 TERMINAL)
  1. When using intelligent tester:

    1. Start the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the intelligent tester ON.

    4. Select the DATA LIST mode on the intelligent tester.

    5. Measure the voltage condition output from the ECU displayed on the intelligent tester.


Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
IG VOLTAGE
ECU power supply voltage:
TOO LOW / NORMAL / TOO HIGH
TOO HIGH: 14 V or more
NORMAL: 9.5 V or 14 V
TOO LOW: Below 9.5 V
-

OK:
"Normal" is displayed.



  1. When not using intelligent tester:



      C121700E13
    1. Disconnect the skid control ECU connector.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage.

      Standard Voltage:
      Tester Connection
      Specified Condition
      S1-46 (IG1) - Body ground
      10 to 14 V

    4. Turn the ignition switch to OFF.

    5. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (GND TERMINAL CONTINUITY)


    C121700E06
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    S1-1 (GND1) - Body ground
    Below 1 Ω
    S1-32 (GND2) - Body ground
    Below 1 Ω

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 1.9 mph (3 km/h) or more for 10 seconds or more.

  1. Check if the same DTCs are detected.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



NG
END
A

REPLACE BRAKE ACTUATOR