DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 0.2 V or less for 2 seconds (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 4.535 V or more for 2 seconds (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 1.75 V or less for 2 seconds (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) met (1 trip detection logic)
|
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| THROTTLE POS | 10 to 24 % | 64 to 96 % |
| THROTTLE POS #2 | 2.1 to 3.1 V | 4.5 to 5.0 V |
| Related DTCs | P0120: Throttle position sensor 1 range check (Fluctuating) P0122: Throttle position sensor 1 range check (Low voltage) P0123: Throttle position sensor 1 range check (High voltage) P0220: Throttle position sensor 2 range check (Fluctuating) P0222: Throttle position sensor 2 range check (Low voltage) P0223: Throttle position sensor 2 range check (High voltage) P2135: Throttle position sensor range check (Correlation) |
| Required Sensors/Components (Main) | Throttle position sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223 (Accelerator pedal ON) 10 seconds: P0120, P0122, P0123, P0220, P0222 and P0223 (Accelerator pedal OFF) Within 0.5 seconds: P2135 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| VTA1 voltage | 0.2 V or less, or 4.535 V or more |
| VTA1 voltage | 0.2 V or less |
| VTA1 voltage | 4.8 V or more |
| VTA2 voltage | 1.75 V or less, or 4.8 V or more |
| VTA2 voltage | 1.75 V or less |
| VTA2 voltage when VTA1 0.2 V or more | 4.8 V or more |
| Either of following conditions A or B met: | - |
| Condition A | - |
| Difference between VTA1 and VTA2 voltages | 0.02 V or less |
| Condition B | - |
| VTA1 voltage | 0.2 V or less |
| VTA2 voltage | 1.75 V or less |
| VTA1 voltage | 0.69 to 4.05 V |
| VTA2 voltage | 2.25 to 4.8 V |

| 1.READ VALUE OF INTELLIGENT TESTER (THROTTLE POS AND THROTTLE POS #2) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ETCS / THROTTLE POS and THROTTLE POS #2.
Check the values displayed on the tester.
| TP#1 (VTA1) When AP Released | TP#2 (VTA2) When AP Released | TP#1 (VTA1) When AP Depressed | TP#2 (VTA2) When AP Depressed | Trouble Areas | Proceed To |
| 0 % | Between 0 V and 0.2 V | 0 % | Between 0 V and 0.2 V | VC circuit open | A |
| 100 % | Between 4.5 V and 5.0 V | 100 % | Between 4.5 V and 5.0 V | E2 circuit open | A |
| 0 % or 100 % | Between 2.1 V and 3.1 V (Fail-safe) | 0 % or 100 % | Between 2.1 V and 3.1 V (Fail-safe) | VTA1 circuit open or ground short | A |
| Approx 19 % (Fail-safe) | Between 0 V and 0.2 V or 4.5 V and 5.0 V | Between 10 % and 24 % (Fail-safe) | Between 0 V and 0.2 V or 4.5 V and 5.0 V | VTA2 circuit open or ground short | A |
| Between 10 % and 24 % | Between 2.1 V and 3.1 V | Between 64 % and 96 % (Not fail-safe) | Between 4.5 V and 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the T1 throttle with motor body connector.
Disconnect the E4 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| VC (T1-5) - VC (E4-23) | Below 1 Ω |
| VTA (T1-6) - VTA1 (E4-20) | |
| VTA2 (T1-4) - VTA2 (E4-19) | |
| E2 (T1-3) - E2 (E4-28) |
| Tester Connections | Specified Conditions |
| VC (T1-5) or VC (E4-23) - Body ground | 10 kΩ or higher |
| VTA (T1-6) or VTA1 (E4-20) - Body ground | |
| VTA2 (T1-4) or VTA2 (E4-19) - Body ground |
Reconnect the throttle with motor body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the T1 throttle with motor body connector.
Turn the ignition switch ON.
Measure the voltage between the terminals of the E4 ECM connector.
| Tester Connections | Specified Conditions |
| VC (E4-23) - E2 (E4-28) | 4.5 to 5.0 V |
Reconnect the throttle with motor body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||