Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

for Preparation Click here

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check No. 1 ignition coil with igniter circuit.
  3. If DTC P0352 is set, check No. 2 ignition coil with igniter circuit.
  4. If DTC P0353 is set, check No. 3 ignition coil with igniter circuit.
  5. If DTC P0354 is set, check No. 4 ignition coil with igniter circuit.
  6. If DTC P0355 is set, check No. 5 ignition coil with igniter circuit.
  7. If DTC P0356 is set, check No. 6 ignition coil with igniter circuit.


DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A082677E02


DTC No.
DTC Detection Conditions
Trouble Areas
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine running (1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil with igniter and ECM
  3. No. 1 to No. 6 ignition coils with igniters
  4. ECM

  1. A031764E02
  2. Reference: Inspection using an oscilloscope
    While cranking or idling, check the waveform between terminals IGT(1 to 6) and E1, and IGF1 and E1 of the ECM connector.
    Items
    Contents
    Terminals
    CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
    CH2: IGF1 - E1
    Equipment Settings
    2 V/Division, 20 ms/Division
    Conditions
    Cranking or idling

MONITOR DESCRIPTION


A115898E01

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 1second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (Cylinder 1) malfunction
P0352: Igniter (Cylinder 2) malfunction
P0353: Igniter (Cylinder 3) malfunction
P0354: Igniter (Cylinder 4) malfunction
P0355: Igniter (Cylinder 5) malfunction
P0356: Igniter (Cylinder 6) malfunction
Required Sensors/Components (Main)
Igniter (Cylinder 1 to 6)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
0.256 seconds and 4 sparks
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions 1 or 2 met
-
1. Following conditions (a) and (b) met:
-
(a) Engine RPM
500 rpm or less
(b) Battery voltage
6 V or more
2. Following conditions (a) and (b) met:
-
(a) Engine RPM
More than 500 rpm
(b) Battery voltage
10 V or more
(c) Number of sparks after CPU is reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


Ignition signal fail count
More than 2 times
Ignition signal fail count is on the right:
When IGF does not return despite sending IGT.

COMPONENT OPERATING RANGE


IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM

WIRING DIAGRAM


A115940E01


A115967E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK SPARK PLUG AND SPARK OF MISFIRING CYLINDER
  1. Check the spark plug and sparks of the misfiring cylinder (Click here).



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGF1 SIGNAL TERMINAL))
A116293E03
  1. Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGF (I1-2) - IGF1 (E4-24)
    Below 1 Ω
    IGF (I2-2) - IGF1 (E4-24)
    IGF (I3-2) - IGF1 (E4-24)
    IGF (I4-2) - IGF1 (E4-24)
    IGF (I5-2) - IGF1 (E4-24)
    IGF (I6-2) - IGF1 (E4-24)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGF (I1-2) or IGF1 (E4-24) - Body ground
    10 kΩ or higher
    IGF (I2-2) or IGF1 (E4-24) - Body ground
    IGF (I3-2) or IGF1 (E4-24) - Body ground
    IGF (I4-2) or IGF1 (E4-24) - Body ground
    IGF (I5-2) or IGF1 (E4-24) - Body ground
    IGF (I6-2) or IGF1 (E4-24) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil with igniter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (IGF1 VOLTAGE)
A115970E07
  1. Disconnect the ignition coil connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E4 and E6 ECM connectors.

    Standard Voltage:
    Tester Connection
    Specified Condition
    IGF1 (E4-24) - E1 (E6-1)
    4.5 to 5.5 V

  1. Reconnect the ignition coil connector.



NG
REPLACE ECM
OK

REPLACE IGNITION COIL ASSEMBLY 

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGT SIGNAL TERMINAL))
A116293E04
  1. Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGT (I1-3) - IGT1 (E4-8)
    Below 1 Ω
    IGT (I2-3) - IGT2 (E4-9)
    IGT (I3-3) - IGT3 (E4-10)
    IGT (I4-3) - IGT4 (E4-11)
    IGT (I5-3) - IGT5 (E4-12)
    IGT (I6-3) - IGT6 (E4-13)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGT (I1-3) or IGT1 (E4-8) - Body ground
    10 kΩ or higher
    IGT (I2-3) or IGT2 (E4-9) - Body ground
    IGT (I3-3) or IGT3 (E4-10) - Body ground
    IGT (I4-3) or IGT4 (E4-11) - Body ground
    IGT (I5-3) or IGT5 (E4-12) - Body ground
    IGT (I6-3) or IGT6 (E4-13) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil with igniter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5, OR IGT6 VOLTAGE)
A115970E08
  1. Measure the voltage between the terminals of the E4 and E6 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGT1 (E4-8) - E1 (E6-1)
    0.1 to 4.5 V
    IGT2 (E4-9) - E1 (E6-1)
    IGT3 (E4-10) - E1 (E6-1)
    IGT4 (E4-11) - E1 (E6-1)
    IGT5 (E4-12) - E1 (E6-1)
    IGT6 (E4-13) - E1 (E6-1)



NG
REPLACE ECM
OK


6.INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5, OR IGT6 VOLTAGE)
A116294E01
  1. Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil connector.

  1. Measure the voltage between the terminals of the E4 and E6 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGT1 (E4-8) - E1 (E6-1)
    4.5 V or more
    IGT2 (E4-9) - E1 (E6-1)
    IGT3 (E4-10) - E1 (E6-1)
    IGT4 (E4-11) - E1 (E6-1)
    IGT5 (E4-12) - E1 (E6-1)
    IGT6 (E4-13) - E1 (E6-1)

  1. Reconnect the ignition coil connector.



NG
Go to step 8
OK


7.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A115969E02
  1. Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    GND (I1-4) - Body ground
    Below 1 Ω
    GND (I2-4) - Body ground
    GND (I3-4) - Body ground
    GND (I4-4) - Body ground
    GND (I5-4) - Body ground
    GND (I6-4) - Body ground

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the wire harness side connector.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (I1-1) - GND (I1-4)
    9 to 14 V
    +B (I2-1) - GND (I2-4)
    +B (I3-1) - GND (I3-4)
    +B (I4-1) - GND (I4-4)
    +B (I5-1) - GND (I5-4)
    +B (I6-1) - GND (I6-4)

  1. Reconnect the ignition coil with igniter connector.



OK
REPLACE IGNITION COIL ASSEMBLY
NG


8.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH)


    A116295E03
  1. Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

  1. Disconnect the I7 ignition switch connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (I1-1) - IG2 (I7-6)
    Below 1 Ω
    +B (I2-1) - IG2 (I7-6)
    +B (I3-1) - IG2 (I7-6)
    +B (I4-1) - IG2 (I7-6)
    +B (I5-1) - IG2 (I7-6)
    +B (I6-1) - IG2 (I7-6)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (I1-1) or IG2 (I7-6) - Body ground
    10 kΩ or higher
    +B (I2-1) or IG2 (I7-6) - Body ground
    +B (I3-1) or IG2 (I7-6) - Body ground
    +B (I4-1) or IG2 (I7-6) - Body ground
    +B (I5-1) or IG2 (I7-6) - Body ground
    +B (I6-1) or IG2 (I7-6) - Body ground

  1. Reconnect the ignition coil with igniter connector.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY