Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY


F051320E01
  1. Install the steering column assembly with the 2 nuts and bolt.

    Torque:
    21 N*m{ 210 kgf*cm , 16 ft.*lbf }

  1. Connect each of the connectors to the steering column assembly.

  1. Connect the wire harness clamps to the steering column assembly.

    CAUTION:
    Use a shop rag to wipe any dirt off the installation plane and column body side.

    NOTICE:
    Be careful not to scratch or soil the installation plane of the steering column.



2. INSTALL NO.2 STEERING INTERMEDIATE SHAFT


F043317E01
  1. Align the matchmarks on the power steering gear and No. 2 steering intermediate shaft.

  1. Install the No. 2 steering intermediate shaft onto the steering gear box with bolt C.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for bolt C



3. INSTALL STEERING SLIDING YOKE
  1. Align the matchmarks on the steering column and steering sliding yoke.

  1. Install the steering sliding yoke onto the steering column assembly and slide it upward.

  1. Align the matchmarks on the intermediate shaft sub-assembly No. 2 and steering sliding yoke.

  1. Install the sliding yoke onto the intermediate shaft sub- assembly No. 2 with bolts A and B.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for bolt A, B



4. INSTALL NO.1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover sub-assembly with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



5. INSTALL STEERING COLUMN HOLE COVER


F051329
  1. Install the steering column hole cover with the 4 clips.



6. INSTALL LOWER INSTRUMENT PANEL LH


    B085788E01
  1. Install the lower instrument panel LH with the 3 bolts <B>.



7. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


B085780E01
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



8. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Engage the 4 clips and install the instrument panel hole cover.



9. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



10. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



11. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



12. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



13. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


    B087476E01
  1. Engage the 8 claws and clip, and install the front door scuff plate.



14. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab)


    B087436E01
  1. Engage the 9 claws and clip, and install the front door scuff plate.



15. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab)


    B087411E01
  1. Engage the 9 claws and install the front door scuff plate.



16. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



17. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY


E076074E01
  1. Engage the claw and install the windshield wiper switch assembly.

  1. Connect the 2 connectors.



18. INSTALL SPIRAL CABLE SUB-ASSEMBLY
  1. Set the turn signal switch in neutral position.

    NOTICE:
    Make sure of the neutral position since the pin of the turn signal switch may be snapped.

  1. Install the spiral cable sub-assembly with the 4 screws.

    NOTICE:
    When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the handle.

  1. Connect the airbag connector and connector.

  1. Install the steering column cover with the 3 screws.



19. INSTALL UPPER STEERING COLUMN COVER
  1. Engage the claw and then install the steering column cover upper.



20. INSTALL LOWER STEERING COLUMN COVER
  1. Engage the 2 claws.

  1. Install the steering column cover lower with the 2 screws.



21. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



22. INSTALL STEERING PAD


H042362

NOTICE:
  1. Never use airbag parts from a different vehicle. When replacing parts, replace them with new ones.
  2. Make sure the wheel pad is installed to the specified torque.
  3. If the wheel pad has been dropped, or there are cracks, dents or other defects in the case or connector, replace the wheel pad with a new one.
  4. When installing the wheel pad, take care that the wiring does not interfere with other parts and is not pinched between other parts.

  1. Support the steering pad with one hand, as shown in the illustration.

  1. Connect the 2 airbag connectors.

  1. Connect the horn ground harness to the steering pad.



    F051342
  1. Confirm that the circumference groove of the "torx" screws fits in the screw case, and install the steering pad.

  1. Using a "torx" socket wrench (T30), install the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



23. INSTALL NO.3 LOWER STEERING WHEEL COVER
  1. Engage the claw and install the No. 3 lower steering wheel cover onto the steering wheel assembly.



24. INSTALL NO.2 LOWER STEERING WHEEL COVER
  1. Engage the claw and install the No. 2 lower steering wheel cover onto the steering wheel assembly.



25. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



27. INSPECT SRS WARNING LIGHT
(Click here)