STEERING COLUMN ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 4. REMOVE NO.2 LOWER STEERING WHEEL COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the steering wheel cover lower No. 2.
| 5. REMOVE NO.3 LOWER STEERING WHEEL COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the No. 3 lower steering wheel cover.
| 6. REMOVE STEERING PAD |
Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference fits in the screw case.
![]() |
Pull the steering pad out of the steering wheel assembly and support the steering pad with one hand, as shown in the illustration.
Disconnect the horn ground harness from the steering pad.
Using a screwdriver, disconnect the airbag connectors.
![]() |
Remove the steering pad.
| 7. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Remove the steering wheel assembly set nut.
Place matchmarks on the steering wheel assembly and main shaft assembly.
Using SST, remove the steering wheel assembly.
| 8. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
Disengage the 2 claws to remove the lower steering column cover.
| 9. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Disengage the claw and then remove the upper steering column cover.
| 10. REMOVE SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the airbag connector and the connector from the spiral cable sub-assembly.
Disengage the 3 claws and remove the spiral cable sub-assembly.
| 11. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Using a screwdriver wrapped with protective tape, disengage the claw and remove the windshield wiper switch assembly.
| 12. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 2 clips and remove the front floor footrest.
| 13. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Disengage the 8 claws and clip, and remove the front door scuff plate.
| 14. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab) |
![]() |
Disengage the 9 claws and clip, and remove the front door scuff plate.
| 15. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab) |
![]() |
Disengage the 9 claws and remove the front door scuff plate.
| 16. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 17. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 18. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 19. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
![]() |
Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.
| 20. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
![]() |
Disengage the 4 clips and remove the instrument panel hole cover.
| 21. REMOVE INSTRUMENT PANEL LOWER LH |
![]() |
Remove the 3 bolts <B> and the lower instrument panel LH.
| 22. REMOVE INSTRUMENT PANEL COVER SUB-ASSEMBLY LOWER |
![]() |
Remove the bolt <B>.
Disengage the 5 clips and remove the instrument lower cover sub-assembly.
Disconnect the 2 connectors.
| 23. REMOVE STEERING COLUMN HOLE COVER |
![]() |
Disengage the 4 clips and remove the steering column hole cover.
| 24. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Remove the No. 1 engine under cover sub-assembly with the 4 bolts.
| 25. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT |
![]() |
Mark matchmarks on the power steering gear assembly and No. 2 steering intermediate shaft.
Remove bolt C and No. 2 steering intermediate shaft from the power steering gear assembly.
| 26. REMOVE STEERING SLIDING YOKE |
Mark matchmarks on the steering sliding yoke, steering intermediate shaft sub-assembly No. 2 and steering intermediate shaft assembly.
Remove bolts A and B from the steering sliding yoke.
Slide the steering sliding yoke up and separate it from the steering intermediate shaft sub-assembly No. 2.
Pull down the steering sliding yoke from the steering intermediate shaft assembly to remove.
| 27. REMOVE STEERING COLUMN ASSEMBLY |
![]() |
Disconnect the connectors and wire harness clamps.
Remove the bolt and 2 nuts, then remove the steering column assembly from the instrument panel reinforcement assembly.