Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1825/56    Short in Front Passenger Side - Side Squib Circuit

DTC    B1826/56    Open in Front Passenger Side - Side Squib Circuit

DTC    B1827/56    Short to GND in Front Passenger Side - Side Squib Circuit

DTC    B1828/56    Short to B+ in Front Passenger Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The side squib (front passenger seat side) circuit consists of the center airbag sensor assembly and the front seat with adjuster frame assembly RH.
The circuit signals the SRS to deploy when airbag deployment conditions are met.
These DTCs are set when a malfunction is detected in the side squib (front passenger seat side) circuit.

DTC No.
DTC Detecting Conditions
Trouble Areas
B1825/56
  1. The center airbag sensor assembly receives a line short circuit signal in the side squib (Front passenger seat side) circuit for 2 seconds
  2. Side squib (Front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat with adjuster frame assembly RH (Side squib [Front passenger seat side])
  3. Center airbag sensor assembly
B11826/56
  1. The center airbag sensor assembly receives an open circuit signal in the side squib (Front passenger seat side) circuit for 2 seconds
  2. Side squib (Front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat with adjuster frame assembly RH (Side squib [Front passenger seat side])
  3. Center airbag sensor assembly
B1827/56
  1. The center airbag sensor assembly receives a short circuit to ground signal in the side squib (Front passenger seat side) circuit for 0.5 seconds
  2. Side squib (Front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat with adjuster frame assembly RH (Side squib [Front passenger seat side])
  3. Center airbag sensor assembly
B1828/56
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the side squib (Front passenger seat side) circuit for 0.5 seconds
  2. Side squib (Front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat with adjuster frame assembly RH (Side squib [Front passenger seat side])
  3. Center airbag sensor assembly

WIRING DIAGRAM


H101930E02


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. If using the intelligent tester (read the 5-digit DTCs):
      Using the intelligent tester, check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC B1825 is output.
      A
      DTC B1826 is output.
      B
      DTC B1827 is output.
      C
      DTC B1828 is output.
      D

    2. If not using the intelligent tester (read the 2-digit DTCs):
      Check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC 56 is output.
      E



B
Go to step 3

C
Go to step 4

D
Go to step 5

E
Go to step 6
A


2.CHECK FLOOR WIRE (FOR SHORT)


    H100874E03
  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - S27-2 (SFP-)
    Always
    1 MΩ or Higher



OK
Go to step 8
NG

REPAIR OR REPLACE FLOOR WIRE 

3.CHECK FLOOR WIRE (FOR OPEN)


    H100874E03
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - S27-2 (SFP-)
    Always
    Below 1 Ω



OK
Go to step 9
NG

REPAIR OR REPLACE FLOOR WIRE 

4.CHECK FLOOR WIRE (TO GROUND)


    H100874E03
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - Body ground
    Always
    1 MΩ or Higher
    S27-2 (SFP-) - Body ground
    Always
    1 MΩ or Higher



OK
Go to step 9
NG

REPAIR OR REPLACE FLOOR WIRE 

5.CHECK FLOOR WIRE (TO B+)


    H100874E03
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - Body ground
    Ignition switch ON
    Below 1 V
    S27-2 (SFP-) - Body ground
    Ignition switch ON
    Below 1 V



OK
Go to step 9
NG

REPAIR OR REPLACE FLOOR WIRE 

6.CHECK FLOOR WIRE (SIDE SQUIB (FRONT PASSENGER SEAT SIDE) CIRCUIT)


    H100874E03
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - Body ground
    Ignition switch ON
    Below 1 V
    S27-2 (SFP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - S27-2 (SFP-)
    Always
    Below 1 Ω
    S27-1 (SFP+) - Body ground
    Always
    1 MΩ or Higher
    S27-2 (SFP-) - Body ground
    Always
    1 MΩ or Higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S27-1 (SFP+) - S27-2 (SFP-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY RH (SIDE SQUIB (FRONT PASSENGER SEAT SIDE))


    H100875E03
  1. Replace the front seat with adjuster frame assembly RH (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 56 is not output.

HINT:
DTCs other than 56 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END 

8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101872E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825 is not output.

HINT:
DTCs other than B1825 may be output at this time, but they are not related to this check.



OK
Go to step 10
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

9.CHECK CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 5, begin from (a). If continuing from any other step, begin from (c).



    H101873E01
  1. Turn ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Using a service wire, connect S27-1 (SFP+) and S27-2 (SFP-) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1826, B1827 and B1828 are not output.

HINT:
DTCs other than B1826, B1827 or B1828 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


10.CHECK FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH
C109226E01

HINT:
If continuing from step 9, begin from (c). If continuing from any other step, being from (a).

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector C.

  1. Connect the connector to the front seat with adjuster frame assembly RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827 and B1828 are not output.

HINT:
DTCs other than B1825, B1826, B1827 or B1828 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH
OK

OTHERS USE SIMULATION METHOD TO CHECK