ROOF HEADLINING (for Access Cab) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Disconnect the EC mirror connector.
Slide the inner rear view mirror cover.
![]() |
Slide the inner rear view mirror.
![]() |
Disengage the 2 claws and remove the inner rear view mirror cover.
| 3. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 2 clips and remove the front floor footrest.
| 4. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 9 claws and clip, and remove the front door scuff plate.
| 5. REMOVE FRONT DOOR SCUFF PLATE RH |
| 6. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 7. REMOVE COWL SIDE TRIM BOARD RH |
| 8. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 7 claws and remove the rear door scuff plate.
| 9. REMOVE REAR DOOR SCUFF PLATE RH |
| 10. REMOVE ROOF SIDE INNER GARNISH COVER LH |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.
| 11. REMOVE ROOF SIDE INNER GARNISH COVER RH |
| 12. REMOVE ROOF SIDE INNER GARNISH CAP LH |
![]() |
Using a "Torx" socket wrench T30, remove the 2 screws.
Disengage the 4 claws and remove the roof side inner garnish cap.
| 13. REMOVE ROOF SIDE INNER GARNISH CAP RH |
| 14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the front door opening trim weatherstrip.
| 15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 16. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.
![]() |
Remove the 2 screws.
Disengage the claw and clip, and remove the front pillar garnish.
![]() |
for LH Side:
Using a clip remover, remove the 3 wire harness clamps.
| 17. REMOVE FRONT PILLAR GARNISH RH |
| 18. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
![]() |
Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.
| 19. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
![]() |
Disengage the 4 clips and remove the instrument panel hole cover.
| 20. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY |
for Automatic Transmission:
Remove the rear console upper panel sub-assembly .
for Manual Transmission:
Remove the rear console upper panel sub-assembly .
| 21. REMOVE REAR CONSOLE BOX ASSEMBLY |
![]() |
Remove the console box carpet.
![]() |
Remove the 2 screws <F> and 2 bolts <B>.
Disengage the 4 claws and remove the rear console box assembly.
| 22. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission) |
![]() |
Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.
| 23. REMOVE FRONT CONSOLE BOX |
for Automatic Transmission:
Remove the front console box .
for Manual Transmission:
Remove the front console box .
| 24. REMOVE AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Using a screwdriver, disengage the 4 clips and remove the air conditioning control assembly.
Disconnect the 2 connectors.
| 25. REMOVE RADIO RECEIVER ASSEMBLY |
![]() |
Remove the 4 bolts.
Disconnect the connector and remove the radio receiver assembly with bracket.
| 26. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 2 claws.
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.
| 27. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL |
![]() |
Remove the 2 bolts <B>.
Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.
Disconnect the connectors.
| 28. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.
Disconnect the connectors.
| 29. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws <E> and the combination meter assembly.
Disconnect the 2 connectors.
| 30. REMOVE INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.
| 31. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.
Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
![]() |
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.
| 32. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Remove the bolt <B>.
Disengage the 2 clips and remove the instrument panel lower finish panel sub-assembly RH.
| 33. REMOVE INSTRUMENT LOWER PANEL |
![]() |
Remove the 3 bolts <B> and the lower instrument panel LH.
| 34. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY |
![]() |
Remove the bolt <B>.
Disengage the 5 clips and remove the instrument lower cover sub-assembly.
Disconnect the 2 connectors.
| 35. REMOVE INSTRUMENT SIDE PANEL |
![]() |
Using a screwdriver, disengage the 3 claws and remove the instrument side panel RH.
| 36. DISCONNECT PASSENGER AIRBAG CONNECTOR |
![]() |
Disconnect the airbag connector.
| 37. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Tape up the steering column cover upper and steering wheel sub-assembly in protective tape.
Disengage the 4 clamps and disconnect the 4 connectors.
Remove the 8 bolts, nut and instrument panel sub-assembly w/ passenger air bag assembly.

| 38. REMOVE BACK PANEL TRIM COVER |
![]() |
Disengage the 6 claws and remove the back panel trim cover.
| 39. REMOVE REAR SEAT INNER BELT ASSEMBLY |
![]() |
Disengage the claw and remove the buckle of the rear seat belt inner.
| 40. REMOVE BACK PANEL TRIM |
![]() |
Disengage the 8 claws and 14 clips, and remove the back panel trim.
| 41. REMOVE QUARTER TRIM LOWER PANEL LH |
![]() |
Remove the bolt and floor anchor of the rear seat belt outer.
![]() |
Disengage the claw and 2 clips, and remove the quarter trim lower panel.
| 42. REMOVE QUARTER TRIM LOWER PANEL RH |
| 43. REMOVE ROOF SIDE INNER GARNISH LH |
![]() |
Disengage the 2 claws and clip, and remove the roof side inner garnish.
| 44. REMOVE ROOF SIDE INNER GARNISH RH |
| 45. REMOVE QUARTER INSIDE TRIM BOARD LH |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the claw and open the cover.
![]() |
Remove the screw.
Disengage the 3 clips and remove the quarter inside trim board.
| 46. REMOVE QUARTER INSIDE TRIM BOARD RH |
| 47. REMOVE ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens.
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws.
Disconnect the room light connector and remove the room light.
| 48. REMOVE ROOF CONSOLE BOX ASSEMBLY |
![]() |
Remove the screw.
Disengage the 2 clips and 3 claws.
Disconnect the accessory meter connector and map lamp connector, and remove the roof console box.
![]() |
Using a clip remover, remove the wire harness clamp.
| 49. REMOVE VISOR ASSEMBLY LH |
![]() |
Remove the 2 screws.
Remove the visor from the visor holder.
| 50. REMOVE VISOR ASSEMBLY RH |
| 51. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder 90° counterclockwise and remove it.
| 52. REMOVE COAT HOOK |
![]() |
Turn the coat hook 90° counterclockwise and remove it.
| 53. REMOVE ROOF HEADLINING ASSEMBLY |
![]() |
Disconnect the frame wire connector.
Disconnect the roof wire connector.
Using a clip remover, remove the 2 wire harness clamps.
![]() |
Remove the roof headlining from the vehicle.
| 54. REMOVE ROOF HEADLINING PAD |
![]() |
Remove the 2 roof headlining pads from the roof headlining.
| 55. REMOVE ROOF WIRE |
![]() |
w/ EC mirror:
Remove the 10 adhesive tapes and roof wire.
w/o EC mirror:
Remove the 8 tapes and roof wire.