Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


    B087583E01
  1. Disconnect the EC mirror connector.

  1. Slide the inner rear view mirror cover.



    B087584E01
  1. Slide the inner rear view mirror.



    B087585E01
  1. Disengage the 2 claws and remove the inner rear view mirror cover.



3. REMOVE SEAT TRACK COVER LH


B087374E01

HINT:
Follow the same procedures as for the opposite side.

  1. Disengage the 2 claws and remove the seat track cover.



4. REMOVE SEAT TRACK COVER RH
  1. for Separate Folding Seat Type:

    1. Remove the seat track cover RH .

  1. for Separate Seat Type Front Passenger Side:

    1. Remove the seat track cover RH .



5. REMOVE FRONT SEAT ASSEMBLY LH


    B087646E01
  1. Disconnect the 2 connectors.

  1. w/ Front Seat Side Airbag:

    1. Disconnect the connector.

  1. Using a clip remover, remove the wire harness clamp.



    B087375E01
  1. Remove the 4 bolts and front seat.



6. REMOVE FRONT SEAT ASSEMBLY RH
  1. for Separate Folding Seat Type:

    1. Remove the front seat assembly RH .

  1. for Separate Seat Type Front Passenger Side:

    1. Remove the front seat assembly RH .



7. REMOVE REAR SEAT CUSHION ASSEMBLY LH


    B087193E01
  1. Remove the 2 bolts and rear seat cushion.



8. REMOVE REAR SEAT CUSHION ASSEMBLY RH


    B087214E01
  1. Remove the 2 bolts and rear seat cushion.



9. REMOVE REAR SEAT BACK HINGE COVER
  1. for LH Side:

    1. Remove the rear seat back hinge cover .

  1. for RH Side:

    1. Remove the rear seat back hinge cover .



10. REMOVE REAR SEAT BACK ASSEMBLY LH


    B087195E01
  1. Remove the 2 bolts and rear seat back.



11. REMOVE REAR SEAT BACK ASSEMBLY RH


    B087215E01
  1. Remove the bolt, rear seat belt outer center and floor anchor of the rear seat belt inner.



    B087217E01
  1. Remove the 2 bolts and rear seat back.



12. REMOVE REAR SEAT BACK HINGE SUB-ASSEMBLY LH


    B087196E01
  1. Remove the 2 bolts and rear seat back hinge.



13. REMOVE REAR SEAT BACK HINGE SUB-ASSEMBLY RH

HINT:
Follow the same procedures as for the rear seat back hinge sub-assembly LH.



14. REMOVE FRONT FLOOR FOOTREST


    B087437E01
  1. Disengage the 2 clips and remove the front floor footrest.



15. REMOVE FRONT DOOR SCUFF PLATE LH


    B087411E01
  1. Disengage the 9 claws and remove the front door scuff plate.



16. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



17. REMOVE COWL SIDE TRIM BOARD LH


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



18. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



19. REMOVE REAR DOOR SCUFF PLATE LH


    B087412E01
  1. Disengage the 8 claws and remove the rear door scuff plate.



20. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the rear door scuff plate LH.



21. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B087413E01
  1. Remove the front door opening trim weatherstrip.



22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip LH.



23. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B087414E01
  1. Remove the rear door opening trim weatherstrip.



24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the rear door opening trim weatherstrip LH.



25. REMOVE FRONT PILLAR GARNISH LH


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the clip and claw and remove the front pillar garnish.



    B087596E01
  1. for LH side:

    1. Using a clip remover, remove the 3 wire harness clamps.



    B087597E02
  1. w/ Curtain Shield Airbag:

    NOTICE:
    Cover the curtain shield airbag with the protective cover as soon as the front pillar garnish is removed.


    1. Thoroughly cover the air bag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.



26. REMOVE FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



27. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.



28. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Disengage the 4 clips and remove the instrument panel hole cover.



29. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. for Automatic Transmission:

    1. Remove the rear console upper panel sub-assembly .

  1. for Manual Transmission:

    1. Remove the rear console upper panel sub-assembly .



30. REMOVE REAR CONSOLE BOX ASSEMBLY


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



31. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission)


    B085773E01
  1. Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.



32. REMOVE FRONT CONSOLE BOX
  1. for Automatic Transmission:

    1. Remove the front console box .

  1. for Manual Transmission:

    1. Remove the front console box .



33. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    B085778E01
  1. Using a screwdriver, disengage the 4 clips and remove the air conditioning control assembly.

    HINT:
    Tape up the screwdriver tip before use.

  1. Disconnect the 2 connectors.



34. REMOVE RADIO RECEIVER ASSEMBLY


E075957
  1. Remove the 4 bolts.

  1. Disconnect the connector and remove the radio receiver assembly with bracket.



35. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088397E01
  1. Disengage the 2 claws.



    B088394
  1. Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.



36. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL


    B085780E01
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.

  1. Disconnect the connectors.



37. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085781E01
  1. Remove the 2 clips.

  1. Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.

  1. Disconnect the connectors.



38. REMOVE COMBINATION METER ASSEMBLY


    B085782E01
  1. Remove the 4 screws <E> and the combination meter assembly.

  1. Disconnect the 2 connectors.



39. REMOVE INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.



40. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B085785E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.

  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B085786E01
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.



41. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY


    B085787E01
  1. Remove the bolt <B>.

  1. Disengage the 2 clips and remove the instrument panel lower finish panel sub-assembly RH.



42. REMOVE INSTRUMENT LOWER PANEL


    B085788E01
  1. Remove the 3 bolts <B> and the lower instrument panel LH.



43. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Remove the bolt <B>.

  1. Disengage the 5 clips and remove the instrument lower cover sub-assembly.

  1. Disconnect the 2 connectors.



44. REMOVE INSTRUMENT SIDE PANEL


    B085790E01
  1. Using a screwdriver, disengage the 3 claws and remove the instrument side panel RH.

    HINT:
    Tape up the screwdriver tip before use.



45. DISCONNECT PASSENGER AIRBAG CONNECTOR


F050426E01
  1. Disconnect the airbag connector.



46. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


    B085807E01
  1. Tape up the steering column cover upper and steering wheel sub-assembly in protective tape.

  1. Disengage the 4 clamps and disconnect the 4 connectors.



  1. Remove the 8 bolts, nut and instrument panel sub-assembly w/ passenger air bag assembly.


    B085804E01



47. REMOVE LAP BELT OUTER ANCHOR COVER


B087415E01

HINT:
Follow the same procedures as for the opposite side.

  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



48. REMOVE CENTER PILLAR LOWER GARNISH LH


    B087416E01
  1. Remove the bolt and floor anchor of the front seat outer belt.



    B087417E01
  1. Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish.



49. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Follow the same procedures as for the center pillar lower garnish LH.



50. REMOVE CENTER PILLAR UPPER GARNISH LH


    B087418E01
  1. Remove the 2 screws.

  1. Disengage the clip and remove the center pillar upper garnish.



51. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:
Follow the same procedures as for the center pillar upper garnish LH.



52. REMOVE LUGGAGE COMPARTMENT SIDE TRAY LH


    B087579E01
  1. Remove the 3 bolts.

  1. Disengage the 8 claws and 3 clips, and remove the luggage compartment side tray.



53. REMOVE REAR SEAT BACK CENTER HINGE SUB-ASSEMBLY


    B087197E01
  1. Remove the 2 bolts and rear seat back center hinge.



54. REMOVE LUGGAGE COMPARTMENT SIDE TRAY RH


    B087580E01
  1. w/ Woofer:

    1. Remove the bolt.

    2. Disengage the 5 claws and 7 clips, and remove the luggage compartment side tray.



    B087581E01
  1. w/o Woofer:

    1. Remove the 3 bolts.

    2. Disengage the 5 claws and 5 clips, and remove the luggage compartment side tray.



55. REMOVE QUARTER TRIM LOWER PANEL LH


    B087419E01
  1. Disengage the 2 claws and 2 clips, and remove the quarter trim lower panel.



56. REMOVE QUARTER TRIM LOWER PANEL RH

HINT:
Follow the same procedures as for the quarter trim lower panel LH.



57. REMOVE QUARTER INSIDE TRIM BOARD LH


    B087324E01
  1. Remove the bolt and remove the floor anchor of the rear seat belt outer.

    HINT:
    Follow the same procedures as for the opposite side.



    B087420E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the claw and open the cover.



    B087421E01
  1. Remove the 3 screws.

  1. Disengage the 2 clips and remove the quarter inside trim board.



58. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the quarter inside trim board LH.



59. REMOVE ROOM LIGHT ASSEMBLY


    B087454E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens.



    B087455E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 3 claws.

  1. Disconnect the room light connector and remove the room light.



60. REMOVE ROOF CONSOLE BOX ASSEMBLY


    B087456E01
  1. Remove the screw.

  1. Disengage the 2 clips and 3 claws.

  1. Disconnect the accessory meter connector and map lamp connector and remove the map lamp.



    B087595E01
  1. Using a clip remover, remove the wire harness clamp.



61. REMOVE ASSIST GRIP SUB-ASSEMBLY


B087422E02

HINT:
Follow the same procedures as for the opposite side.

  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.



    B087423E01
  1. Remove the 2 screws and assist grip.



62. REMOVE ASSIST GRIP PLUG (w/ Curtain Shield Airbag)


B121723E01

HINT:
Follow the same procedures as for the opposite side.

  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.



    B087592E01
  1. Remove the screw.

  1. Disengage the claw and remove the assist grip plug.



63. REMOVE VISOR ASSEMBLY LH


    B087457E01
  1. Remove the 2 screws.

  1. Remove the visor from the visor hol



64. REMOVE VISOR ASSEMBLY RH

HINT:
Follow the same procedures as for the visor assembly LH.



65. REMOVE VISOR HOLDER


B087458E02
  1. Turn the visor holder 90° counterclockwise and remove it.

    HINT:
    Follow the same procedures as for the opposite side.



66. REMOVE COAT HOOK


B087459E02

HINT:
Follow the same procedures as for the opposite side.

  1. Turn the coat hook 90° counterclockwise and remove it.



67. REMOVE ROOF HEADLINING ASSEMBLY


    B087645E01
  1. Disconnect the frame wire connector.

  1. Disconnect the roof wire connector.

  1. Using a clip remover, remove the 2 wire harness clamps.



    B087424E01
  1. Remove the roof headlining from the vehicle.



68. REMOVE ROOF HEADLINING PAD


    B087426E01
  1. Remove the 2 roof headlining pads from the roof headlining.



69. REMOVE ROOF WIRE


    B087427E01
  1. w/ EC Mirror:

    1. Remove the 10 tapes and roof wire.

  1. w/o EC Mirror:

    1. Remove the 8 tapes and roof wire.