Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. PRECAUTION
Click here


2. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Using SST, let the refrigerant gas out.

    SST
    07110-58060   (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least for 90 seconds after disconnecting the cable to prevent the airbag from working.


4. DRAIN ENGINE COOLANT (for 2TR-FE)

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the 4 bolts, then remove the engine under cover No. 1. (PRE RUNNER AND 4WD TYPE)



    G038197E01
  1. Install a vinyl hose onto the radiator side.



    G038198E01
  1. Install a vinyl hose onto the engine side.



    G038199E01
  1. Loosen the engine drain plug.

  1. Loosen the radiator drain plug.

  1. Remove the radiator cap and drain coolant.

  1. Drain the coolant from the reservoir tank.



5. DRAIN ENGINE COOLANT (for 1GR-FE)


A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



6. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    I100926E01
  1. Remove the 2 bolts and separate the suction hose sub-assembly.



    I045031E01
  1. Insert 2 screwdrivers into the 2 piping clamp slots, and while holding them down, disengage the piping clamp claws and the piping clamp.



    I045432E01
  1. Disconnect the suction hose sub-assembly.

    NOTICE:
    1. Do not use a screwdriver or any other tool to disconnect the hose.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

  1. Remove the 2 O-rings from the suction hose sub-assembly.



7. DISCONNECT AIR CONDITIONING TUBE ASSEMBLY


    I045013E01
  1. Remove the bolt.

  1. Disengage the 2 clamps and separate the air conditioning tube assembly.



    I045032E01
  1. Insert 2 screwdrivers into the 2 piping clamp slots, and while holding them down, disengage the piping clamp claws and the piping clamp.



    I045432E01
  1. Disconnect the air conditioner tube.

    NOTICE:
    1. Do not use a screwdriver or any other tool to disconnect the tube.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

  1. Remove the 2 O-rings from the air conditioner tube.



8. DISCONNECT HEATER WATER INLET HOSE (for 2TR-FE)


    I045061E01
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.



9. DISCONNECT HEATER WATER INLET HOSE (for 1GR-FE)


    I045056E01
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.



10. DISCONNECT HEATER WATER OUTLET HOSE (for 2TR-FE)


    I045063E01
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.



11. DISCONNECT HEATER WATER OUTLET HOSE (for 1GR-FE)


    I045058E01
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.



12. REMOVE FRONT WIPER ARM HEAD CAP


E076032E01
  1. Using a screwdriver wrapped with protective tape, remove the 2 front wiper arm head caps.



13. REMOVE FRONT WIPER ARM LH


E076033E01
  1. Operate the wiper, then stop the windshield wiper motor assembly at the automatic stop position.

  1. Remove the nut and front wiper arm LH.



14. REMOVE FRONT WIPER ARM RH

HINT:
Perform the same procedure as above on the opposite side.



15. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


E076036E01
  1. Disengage the 2 claws and remove the front fender to cowl side seal LH.



16. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Perform the same procedure as above on the opposite side.



17. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


E076039E01
  1. Disengage the 2 clips.

  1. Disengage the 15 claws, then remove the cowl top ventilator louver sub-assembly.



18. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


19. REMOVE LOWER NO. 2 STEERING WHEEL COVER


F043322
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the No. 2 lower steering wheel cover.



20. REMOVE LOWER NO. 3 STEERING WHEEL COVER
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the No. 3 lower steering wheel cover.



21. REMOVE HORN BUTTON ASSEMBLY
  1. Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference fits in the screw case.



    H042354
  1. Pull the steering pad out of the steering wheel assembly and support the steering pad with one hand, as shown in the illustration.

    NOTICE:
    When removing the steering pad, take care not to pull the airbag wire harness.

  1. Disconnect the horn ground harness from the steering pad.

  1. Using a screwdriver, disconnect the airbag connectors.



    F045013E01
  1. Remove the steering pad.

    CAUTION:
    1. When placing the steering pad assembly, keep the upper surface of the steering pad facing upward.
    2. Never disassemble the steering pad.



22. REMOVE STEERING WHEEL ASSEMBLY


F044997E01
  1. Remove the steering wheel assembly set nut.

  1. Place matchmarks on the steering wheel assembly and main shaft assembly.

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



23. REMOVE STEERING COLUMN COVER LOWER


F051318E01
  1. Remove the 2 screws.

  1. Disengage the 2 claws to remove the lower steering column cover.



24. REMOVE STEERING COLUMN COVER UPPER


F051319E01
  1. Disengage the claw and then remove the upper steering column cover.



25. REMOVE SPIRAL CABLE SUB-ASSEMBLY


F051337E01
  1. Disconnect the airbag connector and the connector from the spiral cable sub-assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag with harness.

  1. Disengage the 3 claws and remove the spiral cable sub-assembly.



26. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY


E076073E01
  1. Disconnect the 2 connectors.

  1. Using a screwdriver wrapped with protective tape, disengage the claw and remove the windshield wiper switch assembly.

    NOTICE:
    The claw will break if pressed too hard.



27. REMOVE FRONT FLOOR FOOTREST


    B087437E01
  1. Disengage the 2 clips and remove the front floor footrest.



28. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab)


    B087476E01
  1. Disengage the 8 claws and clip, and remove the front door scuff plate.



29. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab)


    B087436E01
  1. Disengage the 9 claws and clip, and remove the front door scuff plate.



30. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab)


    B087411E01
  1. Disengage the 9 claws and remove the front door scuff plate.



31. REMOVE FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



32. REMOVE FRONT DOOR SCUFF PLATE RH (for Access Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



33. REMOVE FRONT DOOR SCUFF PLATE RH (for Double Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



34. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



35. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



36. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



37. REMOVE COWL SIDE TRIM BOARD RH (for Regular Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



38. REMOVE COWL SIDE TRIM BOARD RH (for Access Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



39. REMOVE COWL SIDE TRIM BOARD RH (for Double Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



40. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip LH.



41. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip RH.



42. REMOVE FRONT PILLAR GARNISH LH (for Regular Cab)


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the clip and claw and remove the front pillar garnish.



    B087596E01
  1. for LH Side:

    1. Using a clip remover, remove the 3 wire harness clamps.



43. REMOVE FRONT PILLAR GARNISH LH (for Access Cab)


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the claw and clip, and remove the front pillar garnish.



    B087596E01
  1. for LH Side:

    1. Using a clip remover, remove the 3 wire harness clamps.



44. REMOVE FRONT PILLAR GARNISH LH (for Double Cab)


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the clip and claw and remove the front pillar garnish.



    B087596E01
  1. for LH side:

    1. Using a clip remover, remove the 3 wire harness clamps.



    B087597E02
  1. w/ Curtain Shield Airbag:

    NOTICE:
    Cover the curtain shield airbag with the protective cover as soon as the front pillar garnish is removed.


    1. Thoroughly cover the air bag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.



45. REMOVE FRONT PILLAR GARNISH RH (for Regular Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



46. REMOVE FRONT PILLAR GARNISH RH (for Access Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



47. REMOVE FRONT PILLAR GARNISH RH (for Double Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



48. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.



49. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Disengage the 4 clips and remove the instrument panel hole cover.



50. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085768E01
  1. Remove the shift knob.

  1. Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.



51. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



52. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



53. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B085773E01
  1. Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.



54. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)


    B085777E01
  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



55. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    B085813E01
  1. Remove the shift knob.

  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



56. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)


    B085810E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085812E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



57. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)


    B085774E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085776E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



58. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    B085778E01
  1. Using a screwdriver, disengage the 4 clips and remove the air conditioning control assembly.

    HINT:
    Tape up the screwdriver tip before use.

  1. Disconnect the 2 connectors.



59. REMOVE RADIO RECEIVER ASSEMBLY


E075957
  1. Remove the 4 bolts.

  1. Disconnect the connector and remove the radio receiver assembly with bracket.



60. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088397E01
  1. Disengage the 2 claws.



    B088394
  1. Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.



61. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    B085780E01
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.

  1. Disconnect the connectors.



62. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085781E01
  1. Remove the 2 clips.

  1. Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.

  1. Disconnect the connectors.



63. REMOVE COMBINATION METER ASSEMBLY


    B085782E01
  1. Remove the 4 screws <E> and the combination meter assembly.

  1. Disconnect the 2 connectors.



64. REMOVE INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.



65. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B085785E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.

  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B085786E01
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.



66. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B085785E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.

  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B085786E01
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.



67. REMOVE LOWER INSTRUMENT PANEL LH


    B085788E01
  1. Remove the 3 bolts <B> and the lower instrument panel LH.



68. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Remove the bolt <B>.

  1. Disengage the 5 clips and remove the instrument lower cover sub-assembly.

  1. Disconnect the 2 connectors.



69. REMOVE INSTRUMENT SIDE PANEL RH


    B085790E01
  1. Using a screwdriver, disengage the 3 claws and remove the instrument side panel RH.

    HINT:
    Tape up the screwdriver tip before use.



70. DISCONNECT PASSENGER AIRBAG CONNECTOR


F050426E01
  1. Disconnect the airbag connector.



71. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY W/ PASSENGER AIRBAG ASSEMBLY


    B085807E01
  1. Tape up the steering column cover upper and steering wheel sub-assembly in protective tape.

  1. Disengage the 4 clamps and disconnect the 4 connectors.



  1. Remove the 8 bolts, nut and instrument panel sub-assembly w/ passenger air bag assembly.


    B085804E01



72. REMOVE NO. 1 HEATER TO REGISTER DUCT


    I045018E01
  1. Remove the nut and heater to register duct.



73. REMOVE NO. 3 HEATER TO REGISTER DUCT


    I045019E01
  1. Remove the nut and heater to register duct.



74. REMOVE NO. 2 REAR AIR DUCT (for Double Cab)


    I045021E01
  1. Fold back the floor carpet.

  1. Disengage the 2 claws and remove the air duct rear.



75. REMOVE NO. 1 REAR AIR DUCT (for Double Cab)


    I045020E01
  1. Fold back the floor carpet.

  1. Disengage the 2 claws and remove the air duct rear.



76. REMOVE AIR DUCT ASSEMBLY LH


    I045022E01
  1. Remove the clip.

  1. Disengage the 4 claws and remove the air duct assembly heater.



77. REMOVE AIR DUCT ASSEMBLY RH


    I045023E01
  1. Disengage the 3 claws and remove the air duct assembly.



78. REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET


    I045016E01
  1. Remove the bolt, nut and instrument panel brace mounting bracket LH.



    I045017E01
  1. Remove the bolt, nut and instrument panel brace mounting bracket RH.



79. REMOVE STEERING COLUMN HOLE COVER


F051329
  1. Disengage the 4 clips and remove the steering column hole cover.



80. SEPARATE STEERING SLIDING YOKE
  1. Mark matchmarks on the steering sliding yoke, steering intermediate shaft sub-assembly No. 2 and steering intermediate shaft assembly.

  1. Remove bolts A and B from the steering sliding yoke.

  1. Slide the steering sliding yoke up and separate it from the steering intermediate shaft sub-assembly No. 2.

  1. Pull down the steering sliding yoke from the steering intermediate shaft assembly to remove.



81. REMOVE STEERING COLUMN ASSEMBLY


F051320E01
  1. Disconnect the connectors and wire harness clamps.

  1. Remove the bolt and 2 nuts, then remove the steering column assembly from the instrument panel reinforcement assembly.



82. REMOVE PARKING BRAKE CONTROL LEVER ASSEMBLY (for Lever Type Parking Brake)
  1. Release the parking brake lever.



    F050702E01
  1. Remove the clip and pin and separate the sleeve.

  1. Remove the 2 bolts and parking brake lever assembly.



83. REMOVE ECM (for 2TR-FE)


G036185E01
  1. Disconnect the 4 connectors.

  1. Remove the 2 bolts and nut, then remove the ECM.



84. REMOVE ECM (for 1GR-FE)


G036184E01
  1. Disconnect the 5 connectors.

  1. Remove the 2 bolts and nut, then remove the ECM.



85. SEPARATE DRIVER SIDE JUNCTION BLOCK


    E076135E01
  1. Remove the 2 bolts and bracket.

  1. Remove the 2 nuts and separate the driver side junction block assembly.



86. REMOVE TRANSPONDER KEY ECU ASSEMBLY


    I045014E01
  1. Disconnect the connector.

  1. Remove the nut and the transponder key ECU assembly.



87. REMOVE AIR CONDITIONER AMPLIFIER ASSEMBLY


    I045015E01
  1. Disconnect the connector.

  1. Remove the nut and the air conditioner amplifier assembly.



88. REMOVE AIR CONDITIONING UNIT ASSEMBLY


  1. Disengage the 4 clamps and disconnect the 6 connectors from the air conditioning unit assembly.


    I045003E01

  1. Remove the 3 bolts.

  1. Disconnect the connector.



  1. Disconnect the 2 airbag connectors (Click here).


    I045002E01



  1. Disengage the 20 clamps.


    I045001E01



    I045004E01
  1. Remove the 5 bolts and 2 nuts.

  1. Remove the 2 caps and 7 bolts.

  1. Disengage the reinforcement hook of the air conditioning unit, and remove the reinforcement.



  1. Remove the air conditioner unit assembly.


    I045005E01