Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > INSTALLATION

for Preparation Click here



1. INSTALL INSTRUMENT PANEL CUSHION


2. INSTALL NO. 1 INSTRUMENT PANEL PIN


    B085792E01
  1. Install the 4 No. 1 instrument panel pins with the 4 screws <D>.



3. INSTALL ANTENNA CORD SUB-ASSEMBLY



E075961E01

  1. Engage the 4 claws and install the Radio antenna cord.



4. INSTALL INSTRUMENT PANEL CENTER BRACKET SUB-ASSEMBLY


    B085797E01
  1. Install the instrument panel center bracket sub-assembly with the screw <D>.



5. INSTALL NO.1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B085796E01
  1. Install the instrument panel register with the 4 screws <D> with the fins closed.



6. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY


7. INSTALL DOOR CONTROL RECEIVER


    B085795E01
  1. Install the door control receiver with the 2 screws <D>.



8. INSTALL FOUR WHEEL DRIVE CONTROL ECU


    B085794E01
  1. Install the four wheel drive control ECU with the 2 screws <D>.

    Torque:
    1.2 N*m{ 12 kgf*cm , 11 in.*lbf }



9. INSTALL DEFROSTER NOZZLE ASSEMBLY W/ NO.2 HEATER TO REGISTER DUCT


    B085793E01
  1. Install the defroster nozzle w/ No. 2 heater to register duct with the 5 screws <D>.



10. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY W/ PASSENGER AIRBAG ASSEMBLY
  1. Install the instrument panel sub-assembly w/ passenger air bag assembly with the 8 bolts and nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the 5 clamps and connect the 4 connectors.



  1. Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.


    B085804E01



11. CONNECT PASSENGER AIRBAG CONNECTOR


12. INSTALL INSTRUMENT SIDE PANEL RH


    B085791E01
  1. Engage the 3 claws and install the instrument side RH.



13. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Connect the 2 connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



14. INSTALL LOWER INSTRUMENT PANEL LH


    B085788E01
  1. Install the lower instrument panel LH with the 3 bolts <B>.



15. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH


    B085787E01
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B085815E01
  1. Install the glow compartment door assembly with 3 hinges, holding it horizontal.



    B085785E01
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stopper onto the glove compartment door.



17. INSTALL INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.



18. INSTALL COMBINATION METER ASSEMBLY


    B085782E01
  1. Connect the 2 connectors.

  1. Install the combination meter assembly with the 4 screws <E>.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



19. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B085781E01
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



20. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


B085780E01
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



21. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



22. INSTALL RADIO RECEIVER ASSEMBLY


E075957
  1. Connect the connector.

  1. Install the radio receiver assembly with bracket with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



23. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


B085779E01
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



24. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)


B085776E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085775E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



25. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)


    B085812E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085811E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



26. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    B085814E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



27. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)


    B085777E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.



28. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B085773E01
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.



29. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



30. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Engage the 4 clips and claw, and remove the console upper panel sub-assembly.



31. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085769E01
  1. Engage the 6 clips and claw, and remove the console upper rear panel.

  1. Install the shift knob.



32. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Engage the 4 clips and install the instrument panel hole cover.



33. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



34. INSTALL FRONT PILLAR GARNISH LH (for Regular Cab)


    B087596E01
  1. for LH Side:

    1. Install the 3 wire harness clamps.



    B087444E01
  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.



35. INSTALL FRONT PILLAR GARNISH LH (for Access Cab)


    B087596E01
  1. for LH Side:

    1. Install the 3 wire harness clamps.



    B087444E01
  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



36. INSTALL FRONT PILLAR GARNISH LH (for Double Cab)


    B087596E01
  1. Install the 3 wire harness clamps (LH side only).



    B087444E01
  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



37. INSTALL FRONT PILLAR GARNISH RH (for Regular Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



38. INSTALL FRONT PILLAR GARNISH RH (for Access Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



39. INSTALL FRONT PILLAR GARNISH RH (for Double Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


42. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



43. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



44. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



45. INSTALL COWL SIDE TRIM BOARD RH (for Regular Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



46. INSTALL COWL SIDE TRIM BOARD RH (for Access Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



47. INSTALL COWL SIDE TRIM BOARD RH (for Double Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



48. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


    B087476E01
  1. Engage the 8 claws and clip, and install the front door scuff plate.



49. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab)


    B087436E01
  1. Engage the 9 claws and clip, and install the front door scuff plate.



50. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab)


    B087411E01
  1. Engage the 9 claws and install the front door scuff plate.



51. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



52. INSTALL FRONT DOOR SCUFF PLATE RH (for Access Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



53. INSTALL FRONT DOOR SCUFF PLATE RH (for Double Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



54. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



55. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



56. INSPECT SRS WARNING LIGHT
(Click here)