Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE NO.1 ENGINE UNDER COVER SUB-ASSEMBLY


3. REMOVE NO. 2 ENGINE UNDER COVER (w/ No. 2 Engine Under Cover)


4. DISCONNECT OXYGEN SENSOR


5. REMOVE EXHAUST PIPE
(Click here)


6. REMOVE PROPELLER SHAFT ASSEMBLY FRONT


C098708E02
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



7. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and remove the propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    D033911E01
  1. Pull out the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



8. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    28 N*m{ 285 kgf*cm , 21 ft.*lbf }



9. REMOVE MANIFOLD STAY


F050360
  1. Remove the 3 bolts and manifold stay.



10. REMOVE NO.2 MANIFOLD STAY


F050356
  1. Remove the 3 bolts and manifold stay No. 2.



11. DISCONNECT NO.1 OIL COOLER INLET TUBE


F051602
  1. Remove the 3 bolts and 2 clamps.



    F050350
  1. Using SST, disconnect the oil cooler inlet tube No. 1.

    SST
    09023-12701  



12. DISCONNECT NO.1 OIL COOLER OUTLET TUBE
  1. Using SST, disconnect the oil cooler outlet tube No. 1.

    SST
    09023-12701  



13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


F050351
  1. Remove the nut and disconnect the transmission control cable.

  1. Remove the 2 bolts and disconnect the transmission control cable.



14. SUPPORT AUTOMATIC TRANSMISSION WITH TRANSFER


D028162
  1. Support the automatic transmission assembly with a transmission jack.



15. REMOVE NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


F042938
  1. Remove the 4 bolts on the frame crossmember sub-assembly No. 3.

  1. Remove the 4 nuts, 4 bolts and frame crossmember sub-assembly No. 3.



16. REMOVE REAR NO.1 ENGINE MOUNTING INSULATOR


F042941
  1. Remove the 4 bolts and engine mounting insulator rear from the automatic transmission.



17. DISCONNECT CONNECTOR
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.

  1. Disconnect the transfer shift actuator connector.

  1. Disconnect the indicator switch No. 1 connector.

  1. Disconnect the indicator switch No. 2 connector.



18. DISCONNECT WIRE HARNESS


19. REMOVE STARTER ASSEMBLY


    G036168E01
  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut, then remove the wire harness from terminal 30.

  1. Remove the 2 bolts, then remove the starter assembly.



20. REMOVE FLYWHEEL HOUSING SIDE COVER


F050352
  1. Remove the flywheel housing side cover from the cylinder block.



21. REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER


F050354
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.



    F051601
  1. Remove the 9 bolts.

  1. Separate and remove the automatic transmission.



22. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


23. REMOVE TRANSFER ASSEMBLY


F050671
  1. Remove the 8 transfer adaptor rear mounting bolts.

  1. Pull the transfer straight up and remove it from the transmission.

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.