Home › BRAKE › BRAKE › HYDRAULIC BRAKE BOOSTER (w/ VSC)

HYDRAULIC BRAKE BOOSTER (w/ VSC) > INSTALLATION

for Preparation Click here



1. INSTALL HYDRAULIC BRAKE BOOSTER


F050571
  1. Install a new brake booster gasket onto the hydraulic brake booster.

  1. Install the hydraulic brake booster with the 4 nuts.

    Torque:
    14.2 N*m{ 145 kgf*cm , 10 ft.*lbf }



    F051239E02
  1. Using SST, connect the 4 brake lines to the correct positions of the hydraulic brake booster, as shown in the illustration.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf }



    F051237
  1. Connect the 3 connectors.



2. INSTALL MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

  1. Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.



3. INSTALL DRIVER SIDE JUNCTION BLOCK

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER NO. 1


B085780E01
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



5. INSTALL INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission)


    B085766E01
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



6. INSTALL INSTRUMENT PANEL HOLE COVER (for Manual Transmission)


    B085767E01
  1. Engage the 4 clips and install the instrument panel hole cover.



7. INSTALL COWL SIDE TRIM BOARD (for Regular Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



8. INSTALL COWL SIDE TRIM BOARD (for Access Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



9. INSTALL COWL SIDE TRIM BOARD (for Double Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



10. INSTALL FRONT DOOR SCUFF PLATE (for Regular Cab)


    B087476E01
  1. Engage the 8 claws and clip, and install the front door scuff plate.



11. INSTALL FRONT DOOR SCUFF PLATE (for Access Cab)


    B087436E01
  1. Engage the 9 claws and clip, and install the front door scuff plate.



12. INSTALL FRONT DOOR SCUFF PLATE (for Double Cab)


    B087411E01
  1. Engage the 9 claws and install the front door scuff plate.



13. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

(Click here)


15. INSPECT BRAKE PEDAL HEIGHT


C114968E01
  1. Check the brake pedal height.

    Pedal height from dash panel:
    158.1 to 168.1 mm (6.224 to 6.618 in.)

    NOTICE:
    Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

    If the pedal height is incorrect, adjust the rod operating adapter length.



    C114969E01
  1. Adjust the rod operating adapter length.

    1. Remove the clip and clevis pin.

    2. Loosen the clevis lock nut.

    3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

      Rod operating adapter length A:
      w/ VSC:
      214 to 224 mm (8.425 to 8.818 in.)
      w/o VSC:
      212 to 222 mm (8.346 to 8.740 in.)

    4. Tighten the clevis lock nut.

      Torque:
      25.5 N*m{ 260 kgf*cm , 19 ft.*lbf }

    5. Install the clip and clevis pin.

      1. If the pedal height is incorrect even when the rod operating adapter is adjusted, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket or dash panel.
      2. Even if there is damage, there is no problem if the reserve distance is within the standard value.
      3. If necessary, replace the parts.



16. INSPECT PEDAL FREE PLAY


C114970E01
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

    Pedal free play:
    1 to 6 mm (0.04 to 0.24 in.)



17. INSPECT PEDAL RESERVE DISTANCE


R000934E10
  1. Release the parking brake pedal.
    With the engine running, depress the pedal and measure the pedal reserve distance as shown.

    Pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):
    More than 55 mm (2.17 in.)

    If incorrect, troubleshoot the brake system.



18. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



19. BLEED BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

HINT:
If the brake master cylinder is disassembled, the brake line is disconnected from the brake master cylinder or if the reservoir becomes empty, bleed the brake master cylinder.

  1. Turn the ignition switch to ON, and wait until the pump motor has stopped (step A).

    HINT:
    Pump operating sound can be heard.

  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (step B).

    HINT:
    When pressure in the accumulator is released, the reaction force becomes lighter and the stroke becomes longer.

  1. Repeat step A and B 5 times (step C).

  1. Turn the ignition switch to ON, and check that the pump stops after approximately 8 to 14 seconds.

    NOTICE:
    If the pump does not stop, repeat step C again.



20. BLEED BRAKE LINE
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



21. BLEED MASTER CYLINDER SOLENOID

HINT:
If the brake master cylinder is disassembled, the brake line is disconnected from the brake master cylinder or if the reservoir become empty, bleed the brake master cylinder.



    G035612E03
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select "ACTIVE TEST" mode on the intelligent tester.



    F050558
  1. Connect the vinyl tube to the rear wheel cylinder.

  1. Loosen the bleeder plug.

  1. Select "SRMF & SRMR" to drive the solenoids and bleed air from the rear wheel cylinder (step F).

    NOTICE:
    1. Do not depress the brake pedal.
    2. Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    HINT:
    1. Brake fluid is sent through the pump.
    2. To protect the solenoids, the intelligent tester turns OFF automatically 2 seconds after every solenoid has been turned ON.

  1. Repeat step F until all the air in the brake fluid is bled out.

  1. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedures to bleed the other brake line.

  1. Turn the ignition switch to OFF.

  1. Turn the ignition switch to ON.

  1. Clear DTC (Click here).



22. CHECK FLUID LEVEL IN RESERVOIR
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).



23. CHECK FOR BRAKE FLUID LEAKAGE


24. INSPECT BRAKE MASTER CYLINDER OPERATION
  1. Inspect the battery positive voltage.

    Battery positive voltage:
    10 to 14 V

  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times.

    HINT:
    When pressure in the accumulator is released, the reaction force becomes lighter and the stroke becomes longer.

  1. Check that the brake pedal becomes easy to depress.
    If the pedal does not become easy to depress, check and replace the brake line and hydraulic brake booster.

  1. Turn the ignition switch to ON and check the pump motor operation noise.
    If the pump motor does not operate, check and replace the wire harness and pump motor .

  1. Connect the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select "ACTIVE TEST" mode on the intelligent tester.

      HINT:
      1. Refer to the intelligent tester operator manual for further details.
      2. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.



  1. Check the master cylinder solenoid operation.


    F052425E01


    Inspection Order
    (Step)
    SOL Selected By Active Test
    SOL To Be Activated
    D
    SRCF (SA1)
    SMCF
    E
    SRCF (SA1) and SRCR (SA2)
    SREA and SMCF
    F
    SFRH
    SFRH
    G
    SFLH
    SFLH
    H
    SFRR & SFRH
    SFRR and SFRH
    I
    SFLR & SFLH
    SFLR and SFLH
    J
    SRMF (SMCF, SA3)
    SREC
    K
    SRMF (SMCF, SA3) and SRMR (SMCR, STR)
    STR and SREC
    L
    SRRH
    SRRH
    M
    SRLH
    SRLH
    N
    SRH & SRR
    SRRR and SRRH
    O
    SRLR & SRLH
    SRLR and SRLH

  1. Inspect front VSC solenoid (SMCF) operation (step D).

    HINT:
    1. ON: Activate SMCF and check that the brake pedal cannot be depressed (the pedal feels tight).
    2. OFF: Deactivate SMCF and check that the brake pedal can be depressed.


    1. Select "SRCF (SA1)" on the intelligent tester.

    2. Turn the "SRCF (SA1)" on by the intelligent tester, then depress the brake pedal with stable force and check that the pedal cannot be depressed.
      If the pedal can be depressed, replace the hydraulic brake booster.

      HINT:
      To protect the solenoid, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    3. Release the brake pedal.

    4. When the solenoid is off, depress the brake pedal again and check that the brake pedal can be depressed.
      If the pedal can be depressed, replace the hydraulic brake booster.

  1. Prepare the vehicle.

    1. Jack up and support the vehicle.

    2. Release the parking brake pedal (lever).

    3. Shift the shift lever to the "N" position and check the rear wheels by rotating them by hand.

  1. Inspect front VSC solenoid (SREA) operation (step E).

    HINT:
    1. ON: Activate SREA and SMCF, depress the brake pedal, and then check that the front wheels do not rotate.
    2. OFF: Deactivate SREA and SMCF. Reactivate SMCF, depress the brake pedal, and then check that the front wheels rotate.


    1. Select "SRCR (SA2)" and "SRCF (SMCF)" on the intelligent tester.

    2. Turn the "SRCR (SA2)" and "SRCF (SMCF)" on simultaneously by the intelligent tester, then depress the brake pedal with stable force.

    3. When the solenoids are on, check that the front wheels do not rotate by hand.
      If the front wheels rotate, replace the brake master cylinder.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheels fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheels as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoids are off, turn the "SRCF (SMCF)" on again, then depress the brake pedal and check the front wheels by rotating them by hand.
      If front wheels stop, replace the hydraulic brake booster.

    5. When the "SRCF (SMCF)" is off, depress the brake pedal again and check that the brake pedal can be depressed.
      If the pedal can be depressed, replace the hydraulic brake booster.

  1. Inspect front ABS solenoid (SFRH) operation (step F).

    HINT:
    1. ON: Activate SFRH, depress the brake pedal, and then check that the right front wheel rotates.
    2. OFF: Deactivate SFRH, depress the brake pedal, and then check that the front right wheel does not rotate.


    1. Select "SFRH" on the intelligent tester.

    2. Turn the "SFRH" on by the intelligent tester, then depress the brake pedal with stable force.

    3. When the solenoid is on, check the right front wheel by rotating it by hand.
      If the right front wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoid, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoid is off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
      If the right front wheel rotates, replace the hydraulic brake booster.

  1. Inspect front ABS solenoid (SFLH) operation (step G).

    HINT:
    1. ON: Activate SFLH, depress the brake pedal, and then check that the left front wheel rotates.
    2. OFF: Deactivate SFLH, depress the brake pedal, and then check that the front left wheel does not rotate.


    1. Select "SFLH" on the intelligent tester.

    2. Turn the "SFLH" on by the intelligent tester, then depress the brake pedal with stable force.

    3. When the solenoid is on, check the left front wheel by rotating it by hand.
      If the left front wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoid, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoid is off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
      If the left front wheel rotates, replace the hydraulic brake booster.

  1. Inspect front ABS solenoid (SFRR) operation (step H).

    HINT:
    1. ON: Depress the brake pedal, activate SFRR and SFRH, and then check that the right front wheel rotates.
    2. OFF: Deactivate SFRR and SFRH, depress the brake pedal, and then check that the right front wheel does not rotate.


    1. Select "SFRR & SFRH" on the intelligent tester.

    2. Depress the brake pedal with stable force, then turn the "SFRR & SFRH" on simultaneously by the intelligent tester.

    3. When the solenoids are on, check the right front wheel by rotating it by hand.
      If the right front wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoids are off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
      If the right front wheel rotates, replace the hydraulic brake booster.

  1. Inspect front ABS solenoid (SFLR) operation (step I).

    HINT:
    1. ON: Depress the brake pedal, activate SFLR and SFLH, and then check that the left front wheel rotates.
    2. OFF: Deactivate SFLR and SFLH, depress the brake pedal, and then check that the left front wheel does not rotate.


    1. Select "SFLR & SFLH" on the intelligent tester.

    2. Depress the brake pedal with stable force, then turn the "SFLR & SFLH" on simultaneously by the intelligent tester.

    3. When the solenoids are on, check the left front wheel by rotating it by hand.
      If the left front wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoids are off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
      If the left front wheel rotates, replace the hydraulic brake booster.

  1. Inspect rear VSC solenoid (SREC) operation (step J).

    HINT:
    1. ON: Depress the brake pedal, activate SREC. Release the brake pedal and check that the rear wheels do not rotate.
    2. OFF: Deactivate SREC and check that the rear wheels rotate.


    1. Select "SRMF (SMCF, SA3)" on the intelligent tester.

    2. Depress the brake pedal with stable force, then turn the "SRMF (SMCF, SA3)" on by the intelligent tester.

    3. Release the brake pedal when the solenoid is on, and check that the rear wheels do not rotate by hand.
      If the rear wheels rotate, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheels fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheels as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoid is off, check the rear wheels by rotating them by hand.
      If the rear wheels stop, replace the hydraulic brake booster.

  1. Inspect rear VSC solenoid (STR) operation (step K).

    HINT:
    1. ON: Activate STR and SREC, then check that the rear wheels do not rotate.
    2. OFF: Deactivate STR and SREC. Reactivate SREC and check that the rear wheels rotate.


    1. Select "SRMR (SMCR, STR)" on the intelligent tester.

    2. Turn the "SRMR (SMCR, STR) on simultaneously by the intelligent tester.

    3. When the solenoids are on , check that the rear wheels do not rotate by hand.
      If the rear wheels rotate, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheels fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheels as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoids are off, check the rear wheels by rotating them by hand.
      If the rear wheels stop, replace the hydraulic brake booster.

    5. When the "SRMF (SREC)" is off, depress the brake pedal again and check that the rear wheels do not rotate by hand.
      If the rear wheels rotate, replace the hydraulic brake booster.

  1. Inspect rear ABS solenoid (SRRH) operation (step L).

    HINT:
    1. ON: Activate SRRH, depress the brake pedal, and then check that the right rear wheel rotates.
    2. OFF: Deactivate SRRH, depress the brake pedal, and then check that the right rear wheel does not rotate.


    1. Select "SRRH" on the intelligent tester.

    2. Turn the "SRRH" on by the intelligent tester, then depress the brake pedal with stable force.

    3. When the solenoid is on, check the right rear wheel by rotating it by hand.
      If the right rear wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoid is off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
      If the right rear wheel rotates, replace the hydraulic brake booster.

  1. Inspect front ABS solenoid (SRLH) operation (step M).

    HINT:
    1. ON: Activate SRLH, depress the brake pedal, and then check that the left rear wheel rotates.
    2. OFF: Deactivate SRLH, depress the brake pedal, and then check that the left rear wheel does not rotate.


    1. Select "SRLH" on the intelligent tester.

    2. Turn the "SRLH" on by the intelligent tester, then depress the brake pedal with stable force.

    3. When the solenoid is on, check the left rear wheel by rotating it by hand.
      If the left rear wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoid, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoid is off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
      If the left rear wheel rotates, replace the hydraulic brake booster.

  1. Inspect rear ABS solenoid (SRRR) operation (step N).

    HINT:
    1. ON: Depress the brake pedal, activate SRRR and SRRH, and then check that the right rear wheel rotates.
    2. OFF: Deactivate SRRR and SRRH, depress the brake pedal, and then check that the right rear wheel does not rotate.


    1. Select "SRH & SRR" on the intelligent tester.

    2. Depress the brake pedal with stable force, then turn the "SRH & SRR" on simultaneously by the intelligent tester.

    3. When the solenoids are on, check the right rear wheel by rotating it by hand.
      If the right rear wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoids are off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
      If the right rear wheel rotates, replace the hydraulic brake booster.

  1. Inspect rear ABS solenoid (SRLR) operation (step O).

    HINT:
    1. ON: Depress the brake pedal, activate SRLR and SRLH, and then check that the left rear wheel rotates.
    2. OFF: Deactivate SRLR and SRLH, depress the brake pedal, and then check that the left rear wheel does not rotate.


    1. Select "SRLR & SRLH" on the intelligent tester.

    2. Depress the brake pedal with stable force, then turn the "SRLR & SRLH" on simultaneously by the intelligent tester.

    3. When the solenoids are on, check the left rear wheel by rotating it by hand.
      If the left rear wheel stops, replace the hydraulic brake booster.

      HINT:
      1. To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
      2. When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.

      NOTICE:
      When operating it continuously, set the interval of more than 20 seconds.

    4. When the solenoids are off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
      If the left rear wheel rotates, replace the hydraulic brake booster.

  1. Lower the vehicle.

  1. Disconnect the intelligent tester.