PARKING BRAKE CABLE > INSTALLATION |
| 1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 3 |
![]() |
Install the parking brake cable with the clip onto the parking brake equalizer.
Install the parking brake cable with the 4 bolts.



![]() |
Install the parking brake cable with the 2 bolts onto the backing plate.
| 2. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 1 (for Automatic Transmission) |
![]() |
Install the parking brake cable and provisionally tighten the adjusting nut B and lock nut A.
Install the parking brake cable with the 4 nuts A, 2 clamps B, 2 bolts C.

![]() |
Install the parking brake cable with the clip D, adjusting nut C and lock nut B onto the parking brake control pedal.
Bend the claw A.
| 3. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 1 (for Manual Transmission) |
![]() |
Install the parking brake cable and provisionally tighten the adjusting B nut and lock nut A.
Install the parking brake cable with the 2 nuts A, 2 clamps B and 2 bolts C.

![]() |
Install the parking brake cable onto the parking brake lever with the clip.
Install the sleeve with the pin and clip.
| 4. APPLY HIGH TEMPERATURE GREASE |
![]() |
Apply high temperature grease to the shoe attached surface of the backing plate.
| 5. INSTALL REAR BRAKE SHOE |
![]() |
Apply high temperature grease to the adjusting bolt.
![]() |
Install the parking brake shoe lever LH and parking brake shoe strut set with the shoe return spring onto the rear brake shoe.
![]() |
Using pliers, install the parking brake shoe strut set, parking brake reaction lever and parking brake shoe lever LH with 2 new C-washers.
![]() |
Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.
![]() |
Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.
| 6. INSTALL FRONT BRAKE SHOE |
Install the automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut lower onto the front brake shoe.
![]() |
Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.
![]() |
Install the tension spring onto the front brake shoe and rear brake shoe.
![]() |
Using needle-nose pliers, install the return spring.
![]() |
Using SST, install the shoe return spring onto the front brake shoe.
| 7. INSPECT REAR DRUM BRAKE INSTALLATION |
Check that each part is installed properly.

![]() |
Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameters is the specified shoe clearance.
| 8. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY |
Install a new drum gasket onto the rear brake drum.
Install the rear brake drum.
| 9. ADJUST REAR DRUM BRAKE SHOE CLEARANCE |
![]() |
Provisionally install the hub nuts.
Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.
Using a screwdriver, release the adjuster 15 notches.
Install the hole plug.
| 10. INSTALL REAR WHEEL |
| 11. INSTALL PARKING BRAKE CABLE JOINT PROTECTOR (for Bench Seat Type) |
![]() |
Install the 3 bolts and parking brake cable joint protector.
Return the floor carpet to its original position.
Return the seat to its original position.
| 12. INSTALL VOLTAGE INVERTER ASSEMBLY (w/ Voltage Inverter) |
![]() |
Connect the 2 connectors and install the 2 wire harness clamps.
![]() |
Install the 6 bolts.
| 13. INSTALL CENTER AIRBAG SENSOR ASSEMBLY |
Check that the ignition switch is turned to OFF.
Check that the cable is disconnected from the battery negative terminal.
Provisionally install the air bag sensor assembly center with the 3 bolts.
Tighten the 3 bolts to the specified torque.
Check that there is no slack in the installation parts of the center airbag sensor assembly.
Connect the holder (with connectors) to the center airbag sensor assembly.
Check that the waterproof sheet is properly set.
| 14. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type) |
![]() |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
| 15. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type) |
![]() |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
Install the shift knob.
| 16. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type) |
![]() |
Engage the 2 clips and claw, and install the front console box.
Install the clip and 2 bolts <A>.
![]() |
Install the No. 2 box bottom mat.
Install the instrument panel cup holder.
Install the box bottom mat.
Install the shift knob.
| 17. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type) |
![]() |
Engage the 2 clips and claw, and install the front console box.
Install the clip and 2 bolts <A>.
![]() |
Install the No. 2 box bottom mat.
Install the instrument panel cup holder.
Install the box bottom mat.
Install the shift knob.
| 18. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) |
![]() |
Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.
| 19. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
![]() |
Engage the 4 claws and install the console box rear.
Install the 2 screws <F> and 2 bolts <B>.
![]() |
Install the console box carpet.
| 20. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type) |
![]() |
Engage the 6 clips and claw, and remove the console upper rear panel.
Install the shift knob.
| 21. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type) |
![]() |
Engage the 4 clips and claw, and remove the console upper panel sub-assembly.
| 22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 23. INSPECT SRS WARNING LIGHT |
| 24. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission) |
Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.
| 25. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transmission) |
Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.
| 26. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission) |
Confirm that the parking brake pedal is released.
![]() |
Loosen the lock nut A and turn the adjusting nut B until the parking brake pedal travel is corrected to the specified value.
Tighten the lock nut.
Check whether the parking brake drags or not.
When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.
| 27. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transmission) |
Confirm that the parking brake lever is released.
![]() |
Loosen the lock nut A and turn the adjusting nut B until the parking brake lever travel is corrected to the specified value.
Tighten the lock nut.
Check whether the parking brake drags or not.
When operating the parking brake lever, check that the parking brake lever indicator light comes on.