PARKING BRAKE CABLE > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type) |
![]() |
Remove the shift knob.
Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.
| 4. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type) |
![]() |
Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.
| 5. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
![]() |
Remove the console box carpet.
![]() |
Remove the 2 screws <F> and 2 bolts <B>.
Disengage the 4 claws and remove the rear console box assembly.
| 6. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) |
![]() |
Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.
| 7. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type) |
![]() |
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 8. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type) |
![]() |
Remove the shift knob.
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 9. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 10. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 11. REMOVE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Disconnect the holder (with connectors) from the center airbag sensor assembly.
Remove the 3 bolts and the center airbag sensor assembly.
| 12. REMOVE VOLTAGE INVERTER ASSEMBLY (w/ Voltage Inverter) |
![]() |
Remove the 6 bolts.
![]() |
Disconnect the 2 connectors and remove the 2 wire harness clamps.
| 13. REMOVE PARKING BRAKE CABLE JOINT PROTECTOR (for Bench Seat Type) |
Slide the seat to the rearmost position.
Pull up the floor carpet around the cable joint protector, along its seams.
![]() |
Remove the 3 bolts and parking brake cable joint protector.
| 14. REMOVE REAR WHEEL |
| 15. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY |
![]() |
Release the parking brake, and remove the rear brake drum.
If the rear brake drum cannot be removed easily, perform the following procedures.
Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjusting lever away from the adjuster.
Using another screwdriver, contract the brake shoe by turning the adjusting bolt.
Remove the drum gasket from the rear brake drum.
| 16. REMOVE FRONT BRAKE SHOE |
![]() |
Using SST, remove the shoe return spring from the front brake shoe.
![]() |
Using needle-nose pliers, remove the return spring.
![]() |
Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.
Remove the parking brake shoe strut lower.
Remove the tension spring and front brake shoe.
Remove the automatic adjust lever spring and automatic adjust lever LH from the front brake shoe.
| 17. REMOVE REAR BRAKE SHOE |
![]() |
Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.
![]() |
Using needle-nose pliers, disconnect the parking brake cable No. 3 and remove the rear brake shoe.
![]() |
Using a screwdriver, remove the 2 C-washers, parking brake shoe lever, parking brake reaction lever and parking brake shoe strut set.
| 18. REMOVE PARKING BRAKE CABLE ASSEMBLY NO. 1 (for Automatic Transmission) |
Release the parking brake.
![]() |
Disengage the claw A.
Remove the lock nut B, adjusting nut C and clip D and disconnect the parking brake cable from the parking brake control pedal.
Remove the 4 nuts A, 2 clamps B and 2 bolts C from the parking brake cable.

![]() |
Remove the lock nut A, adjusting nut B and parking brake cable from the parking brake equalizer.
| 19. REMOVE PARKING BRAKE CABLE ASSEMBLY NO. 1 (for Manual Transmission) |
Release the parking brake lever.
![]() |
Disengage the clip, remove the pin and separate the sleeve.
Disengage the clip and disconnect the parking brake cable from the parking brake lever.
Remove the 2 nuts A, 2 clamps B and 2 bolts C from the parking brake cable.

![]() |
Remove the lock nut A, adjusting nut B and parking brake cable from the parking brake equalizer.
| 20. REMOVE PARKING BRAKE CABLE ASSEMBLY NO. 3 |
![]() |
Remove the 2 bolts and disconnect the parking brake cable from the backing plate.
Remove the 4 bolts from the parking brake cable.



![]() |
Disengage the clip and disconnect the parking brake cable from the parking brake equalizer.