Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL PUMP (for 2WD)

OIL PUMP (for 2WD) > INSTALLATION

for Preparation Click here



1. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


A076300E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09226-10010  

  1. Apply MP grease to the oil seal lip.



2. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material. Be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.



    G036305E01
  1. Install a new O-ring onto the LH cylinder head as shown in the illustration.



    G036306E01
  1. Apply continuous beads of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the 4 locations shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent



    A076303E04
  1. Apply continuous beads of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the timing chain cover as shown in the illustration.

    Seal packing:
    Water pump part:
    Part No. 08826-00100 or equivalent
    Other parts:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. Install the timing chain cover within 3 minutes of applying the seal packing. Timing chain cover bolts and nuts must be tightened within 15 minutes of installation. Otherwise, the seal packing must be removed and reapplied.
    2. Do not apply seal packing to portion A shown in the illustration.



    A076304E02
  1. Align the key way of the oil pump drive rotor with the rectangular portion of the crankshaft timing gear, and slide the timing chain cover into place.



    G036303E02
  1. Install the timing chain cover with the 24 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Pay attention not to wrap the chain and slipper over the timing chain cover seal line.

    Each bolt length is as follows:
    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    55 mm (2.17 in.)



3. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
  1. Install a new gasket and the oil filter bracket with the 3 bolts and 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



4. INSTALL VVT SENSOR
  1. LH bank side VVT sensor:

    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

    2. Install the VVT sensor with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Connect the VVT sensor connector.

    4. Connect the water by-pass hoses No. 4 and No. 5.

  1. RH bank side VVT sensor:

    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

    2. Install the VVT sensor with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Connect the VVT sensor connector.



5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Install the 2 camshaft timing oil control valves with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 connectors.



6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076311E02
  1. Install the cylinder head cover within 3 minutes of applying seal packing. Tighten the cylinder head cover bolts and nuts within 15 minutes of installing the cylinder head cover. Otherwise, the seal packing mush be removed and reapplied.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the cylinder head cover within 3 minutes after applying the seal packing. After installing it, cylinder head cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

  1. Install the seal washers onto the bolts.



    A076503E03
  1. Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut

    HINT:
    Each bolt length is as follows.
    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    60 mm (2.36 in.)



7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076310E02
  1. Apply a continuous bead of seal packing (diameter 2 to 3 mm (0.08 to 0.12 in.)) to the cylinder head and timing chain cover as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the cylinder head cover within 3 minutes of applying the seal packing. Tighten the cylinder head cover bolts and nuts within 15 minutes of installing the cylinder head cover. Otherwise, the seal packing must be removed and reapplied.

  1. Install the seal washers onto the bolts.



    A072943E03
  1. Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut

    HINT:
    Each bolt length is as follows.
    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    60 mm (2.36 in.)



8. INSTALL IGNITION COIL ASSEMBLY
  1. LH bank side VVT sensor:

    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

    2. Install the VVT sensor with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Connect the VVT sensor connector.

    4. Connect the water by-pass hoses No. 4 and No. 5.

  1. RH bank side VVT sensor:

    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

    2. Install the VVT sensor with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Connect the VVT sensor connector.



9. INSTALL OIL PAN SUB-ASSEMBLY


G037340E03
  1. Apply continuous beads of seal packing to the places shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    Seal width:
    2 to 3 mm (0.079 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after installation.



    G038130E02
  1. Loosely install the oil pan with the 16 bolts and 2 nuts.

    HINT:
    Bolt length:
    20 mm (0.79 in.) for bolt A,
    40 mm (1.57 in.) for bolt B

  1. Uniformly tighten the 16 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



10. INSTALL OIL STRAINER SUB-ASSEMBLY


G036832E02
  1. Install a new gasket and the oil strainer with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



11. INSTALL NO.2 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil pan and oil pan No. 2.



    G036802E01
  1. Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the oil pan No. 2 within 3 minutes of applying the seal packing. Tighten the oil pan No. 2 bolts and nut within 15 minutes of installing the oil pan. Otherwise, the seal packing must be removed and reapplied.



    G036799E02
  1. Install the oil pan No. 2 with the 15 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolts
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf } for nuts



12. INSTALL CRANKSHAFT PULLEY


A076309E02
  1. Using SST, install the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    250 N*m{ 2,549 kgf*cm , 184 ft.*lbf }



13. INSTALL NO.1 IDLER PULLEY SUB-ASSEMBLY


A076438E01
  1. Install the idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    DOUBLE is marked on the idler pulley No. 1 to distinguish it from the idler pulley No. 2.



14. INSTALL NO.2 IDLER PULLEY SUB-ASSEMBLY


A076338E01
  1. Install the 2 idler pulleys with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



15. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


A076445E03

NOTICE:
A bolt in position A is not reusable.

HINT:
Each bolt length is as follows:

Position
Length
A
70 mm (2.76 in.)
B, C, D and E
33 mm (1.30 in.)
  1. Use a new bolt in position A.

  1. Finger-tighten the bolts in positions A and E and install the bracket.

  1. Tighten the bolts in positions A and E.

    Torque:
    36 N*m{ 267 kgf*cm , 27 ft.*lbf }

  1. Tighten the bolts in positions B, C and D.

    Torque:
    36 N*m{ 267 kgf*cm , 27 ft.*lbf }



16. INSTALL WATER INLET
  1. Install a new gasket onto the water inlet with thermostat.

  1. Install the water inlet with thermostat with the 3 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



17. INSTALL OIL LEVEL GAUGE GUIDE


18. INSTALL ENGINE ASSEMBLY
(Click here)


19. INSTALL BATTERY


20. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:

    Transmission
    Capacity
    Manual Transmission
    9.7 liters (10.3 Us qts, 8.5 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (a) through (h) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.



21. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Capacity:
    2WD:
    Drain and refill with oil filter change
    4.5 liters (4.8 US qts, 4.0 lmp. qts)
    Drain and refill without oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Dry fill
    5.6 liters (5.9 US qts, 4.9 lmp. qts)
    PRE RUNNER and 4WD:
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 lmp. qts)

  1. Reinstall the oil filler cap.



22. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



23. CHECK FOR ENGINE OIL LEAKAGE


24. CHECK FOR FUEL LEAKAGE


25. CHECK FOR EXHAUST GAS LEAKAGE


26. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.



    G035612E02
  1. When using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Select the following menu items: DIAGNOSIS / ENHANCED OBD ll / DATA LIST / IGN ADVANCE.

    3. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24°CA BTDC during idling (Transmission in neutral position)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A118802E01
  1. When not using intelligent tester.

    1. Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to connect the terminals wrongly. It causes breakage of the engine.

    2. Remove the air cleaner.



    3. A076315E02
    4. Pull out the wire harness as shown in the illustration.

    5. Connect the tester probe of a timing light to the wire of the ignition coil connector for No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects the first signal.
      1. After checking, be sure to wrap the wire harness with tape.



    6. A076316E01
    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12°CA BTDC during idling (Transmission in neutral position)

    8. Remove the SST from the DLC3.

    9. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24°CA BTDC during idling (Transmission in neutral position)

    10. Install the air cleaner.



27. INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.



    G035612E02
  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Select the following menu items: DIAGNOSIS / ENHANCED OBD ll / DATA LIST / ENGINE SPD.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)



    A118802E02
  1. When not using the intelligent tester:

    1. Using SST, connect the terminal 8 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Race the engine speed at 2,500 rpm for approximately 90 seconds.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)



28. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2,500 rpm.

    HINT:
    1. Complete the measurement within 3 minutes.
    1. When carrying out the 2 modes (idling and 2,500 rpm) test, the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        1. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        1. Intake manifold
        1. Throttle body
        1. IAC valve
        1. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        1. Faulty engine coolant temperature sensor
        1. Faulty mass air flow meter
        1. Faulty ECM
        1. Faulty injectors
        1. Faulty throttle position sensor