DTC B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction |
DTC B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction |
| DTC No. | DTC Detections Conditions | Trouble Areas |
| B1630/23 |
|
|
| B1635/24 |
|
|

| 1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
Check the DTC (Click here).
| Result | Proceed to |
| DTC B1630/23 is output. | A |
| DTC B1635/24 is output. | B |
| DTC B1630/23 and B1635/24 are output. | C |
| Neither DTC B1630/23 nor B1635/24 is output. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTOR OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the side airbag sensor assembly LH and the rear airbag sensor LH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.
Using SST, connect S13-2 (BCL+) and S13-1 (BCL-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 6.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| S11-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Always | 1 MΩ or Higher |
| S11-2 (BCL-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 8.CHECK REAR AIRBAG SENSOR LH |
![]() |
Connect the connector to the side airbag sensor assembly LH.
Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1630/23 is output. | A |
| DTC B1635/24 is output. | B |
| Neither DTC B1630/23 nor B1635/24 is output. | C |
|
| ||||
|
| ||||
| A | |
| 9.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1630/23 is output. | A |
| DTC B1635/24 is output. | B |
| Neither DTC B1630/23 nor B1635/24 is output. | C |
|
| ||||
|
| ||||
| A | |
| 10.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 11.CHECK REAR AIRBAG SENSOR LH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the rear airbag sensor LH (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 12.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the side airbag sensor assembly RH and the rear airbag sensor RH.
|
| ||||
| OK | |
| 13.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly RH side and airbag sensor rear RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 14.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.
Using SST, connect S14-2 (BCR+) and S14-1 (BCR-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 15.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 16.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| S12-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 17.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Always | 1 MΩ or Higher |
| S12-2 (BCR-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 18.CHECK REAR AIRBAG SENSOR RH |
![]() |
Connect the connector to the side airbag sensor assembly RH.
Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1635/24 is output. | A |
| DTC B1630/23 is output. | B |
| Neither DTC B1630/23 nor B1635/24 is output. | C |
|
| ||||
|
| ||||
| A | |
| 19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1635/24 is output. | A |
| DTC B1630/23 is output. | B |
| Neither DTC B1630/23 nor B1635/24 is output. | C |
|
| ||||
|
| ||||
| A | |
| 20.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 21.REPLACE REAR AIRBAG SENSOR RH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the rear airbag sensor RH (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 22.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the side airbag sensor assembly LH and the rear airbag sensor LH.
Check that the connectors are properly connected to the side airbag sensor assembly RH and the rear airbag sensor RH.
|
| ||||
| OK | |
| 23.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly LH side and airbag sensor rear LH side) are not damaged (Click here).
Check that the connectors (on the side airbag sensor assembly RH side and airbag sensor rear RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 24.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.
Using SST, connect S13-2 (BCL+) and S13-1 (BCL-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 25.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 26.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| S11-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 27.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Always | 1 MΩ or Higher |
| S11-2 (BCL-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 28.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.
Using SST, connect S14-2 (BCR+) and S14-1 (BCR-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 29.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 30.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| S12-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 31.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Always | 1 MΩ or Higher |
| S12-2 (BCR-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 32.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 33.REPLACE REAR AIRBAG SENSOR RH |
![]() |
Connect the connectors to the side airbag sensor assembly RH, the side airbag sensor assembly LH and center airbag sensor assembly.
Replace the rear airbag sensor RH and the rear airbag sensor LH (Click here).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||