Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the status of the brake operation.

DTC No.
DTC Detecting Condition
Trouble Areas
C1249/49
ECU terminal IG1 voltage 9.5 V to 17.0 V and ABS non-operational, open in stop light switch circuit continues for 0.3 seconds or more.
  1. Stop light assembly
  2. Stop light switch circuit
  3. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM


C124774E01


C124793E01


INSPECTION PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Pedal condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF

    HINT:
    Check the stop light bulbs as they may have burnt out.



NG
Go to step 4
OK


2.INSPECT SKID CONTROL ECU (STP TERMINAL VOLTAGE)


    C121700E15
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-7 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    S1-7 (STP) - Body ground
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V

  1. Reconnect the skid control ECU connector.

    Result
    Proceed to
    OK (When troubleshooting in accordance with DTC CHART)
    A
    OK (When troubleshooting in accordance with PROBLEM SYMPTOMS TABLE)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are detected.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID 

4.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C124796E01
  1. Disconnect the stop light switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Switch Connection
    Tester Condition
    Specified Condition
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin pushed in
    1 - 2
    10 kΩ or higher

  1. Reconnect the stop light switch connector.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


5.INSPECT STOP LIGHT CONTROL RELAY
  1. Remove the STOP LP CTRL relay from the engine room R/B and J/B.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher

  1. Apply the battery voltage between terminals 1 (+) and 2 (-).

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    3 - 4
    10 kΩ or higher
    3 - 5
    Below 1 Ω

  1. Reinstall the STOP LP CTRL relay.



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)


    C121702E03
  1. Disconnect the skid control ECU connector.

  1. Disconnect the stop light switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    S1-45 (STP2) - S10-1 (STP)
    Below 1 Ω

  1. Reconnect the stop light switch connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are detected.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID