Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1246/46    Master Cylinder Pressure Sensor Malfunction

for Preparation Click here


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the master cylinder solenoid.

C124773E01

VM/C1 (VCM): Master Cylinder Pressure Sensor Power Supply Output
PM/C1 (PMC): Master Cylinder Pressure Sensor Signal Input
M/C1 GND: Master Cylinder Pressure Sensor Ground

DTC No.
DTC Detecting Conditions
Trouble Areas
C1246/46
When either of following conditions detected:
1. All of the following conditions continue for at least 30 seconds.
  1. Vehicle speed more than 4 mph (7 km/h).
  2. PM/C1 terminal voltage does not change by more than 0.005 V once it exceeds 0.86 V.
2. PM/C1 terminal receives noise at least 7 times within 5 seconds.
3. All of following conditions continue for at least 5 seconds.
  1. Stop switch OFF.
  2. PM/C1 terminal voltage more than 0.86 V or less than 0.3 V.
4. All of following conditions continue for at least 1.2 seconds.
  1. IG1 terminal voltage between 9.5 V and 17.0 V.
  2. VM/C1 terminal voltage not within 4.4 V and 5.6 V.
5. All of following conditions continue for at least 1.2 seconds.
  1. VM/C1 terminal voltage between 4.4 V and 5.6 V.
  2. PM/C1 terminal voltage not within 0.14 V and 4.85 V.
  1. Master cylinder pressure sensor
  2. Master cylinder pressure sensor circuit
  3. Master cylinder solenoid (skid control ECU)
  4. Stop light circuit

INSPECTION PROCEDURE

HINT:
Start the inspection from step 1 when using a intelligent tester and start from step 3 when not using a intelligent tester.

1.READ VALUE OF DATA LIST (MASTER CYLINDER PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester ON.

  1. Select the DATA LIST mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    MAS CYL PRS 1
    Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V
    1. When brake pedal released: 0.3 to 0.9 V
    2. When stop lamps turned on: 0.3 to 0.9 V
    Reading increases when brake pedal depressed

  1. Check that the master pressure value of the master cylinder pressure sensor displayed on the intelligent tester changes when the brake pedal is depressed.

    Result
    Proceed to
    Master cylinder pressure sensor value becomes normal
    A
    Master cylinder pressure sensor value changes but not normal
    B
    Master cylinder pressure sensor value does not change
    C



B
Go to step 3

C
REPLACE MASTER CYLINDER SOLENOID
A


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are detected.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID 

3.CHECK BRAKE PEDAL HEIGHT
  1. Check the brake pedal height.

  1. Check the stop lamp switch installation.

    OK:
    The brake pedal and stop lamp switch are normal.



NG
ADJUST BRAKE PEDAL HEIGHT
OK


4.INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (STP TERMINAL)


    C121700E07
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-7 (STP) - Body ground
    Brake pedal depressed
    8 to 16 V
    S1-7 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are detected.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID