Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > VSC TRAC Warning Light Remains ON

for Preparation Click here


DESCRIPTION

When the skid control ECU stores DTCs, the VSC and TRAC functions are deactivated, the VSC TRAC warning light comes on in the combination meter.

WIRING DIAGRAM


C124780E01


C124794E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.CHECK DTC
  1. Check if DTCs for VSC are recorded.

    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2.INSPECT SKID CONTROL ECU CONNECTOR
  1. Check that the ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


3.INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (IG1 TERMINAL)
  1. When using intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine.

    3. Select the DATA LIST mode on the intelligent tester.

    4. Measure the voltage output from the ECU displayed on the intelligent tester.

      Item
      Measurement Item / Range (Display)
      Normal Condition
      Diagnostic Note
      IG VOLTAGE
      ECU power supply voltage:
      TOO LOW / NORMAL / TOO HIGH
      TOO HIGH: 14 V or more
      NORMAL: 9.5 to 14V
      TOO LOW: Below 9.5 V
      -

      OK:
      "Normal" is displayed.



  1. When not using intelligent tester:



      C121700E02
    1. Disconnect the skid control ECU connector.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage.

      Standard:
      Tester Connection
      Specified Condition
      S1-46 (IG1) - Body ground
      10 to 14 V

    4. Turn the ignition switch to OFF.

    5. Reconnect the skid control ECU connector.


Result
Proceed to
OK (models with rear diff. lock)
A
OK (models without rear diff. lock)
B
NG
C


B
Go to step 6

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


4.INSPECT REAR DIFFERENTIAL LOCK SWITCH


    I044055E01
  1. Remove the rear diff. lock switch.

  1. Disconnect the rear diff. lock switch connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    D5-3 - D5-4
    Released
    10 kΩ or higher
    D5-3 - D5-4
    Pushed in
    Below 1 Ω

  1. Reconnect the rear diff. lock switch connector.

  1. Reinstall the rear diff. lock switch.



NG
REPLACE REAR DIFFERENTIAL LOCK SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - REAR DIFFERENTIAL LOCK SWITCH)


    F051295E01
  1. Disconnect the 4WD control ECU connector.

  1. Disconnect the rear diff. lock connector

  1. Measure the resistance.

    Standard (4WD):
    Tester Connection
    Specified Condition
    F12-16 (R) - D5-4
    Below 1 Ω
    F12-16 (R) - Body ground
    10 kΩ or higher

    Standard (2WD):
    Tester Connection
    Specified Condition
    F14-4 (R) - D5-4
    Below 1 Ω
    F14-4 (R) - Body ground
    10 kΩ or higher

  1. Reconnect the rear diff. lock connector.

  1. Reconnect the 4WD control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)


    F049577E03
  1. Disconnect the skid control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    C9-38 - S1-36 (VSCW)
    Below 1 Ω

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    S1-36 (VSCW) - Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT COMBINATION METER ASSEMBLY
  1. Check the combination meter system (Click here).

    OK:
    Combination meter is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

REPLACE MASTER CYLINDER SOLENOID