DTC P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0776 |
|
|
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th | 5th |
| *1: Actual gear position under SL2 stuck ON malfunction | 1st | 2nd | 3rd | 4th | N* |
| Related DTCs | P0776: Shift solenoid valve SL2/ON malfunction |
| Required sensors/Components (Main) | Shift solenoid valve SL2 |
| Required sensors/Components (Related) | Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | ON malfunctions (A), (B) and (C): 0.4 seconds ON malfunction (D): 3 seconds ON malfunction (E): 0.5 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present. | P0115 - P0118: ECT sensor P0125: Insufficient ECT for Closed Loop P0500: VSS P0748 - P0799: Trans solenoid (range) |
| Turbine speed sensor (NT) circuit | Functioning normally |
| Output speed sensor (SP2) circuit | Functioning normally |
| Shift solenoid "A" (S1) circuit | Functioning normally |
| Shift solenoid "B" (S2) circuit | Functioning normally |
| Shift solenoid "E" (SR) circuit | Functioning normally |
| Pressure control solenoid "A" (SL1) circuit | Functioning normally |
| Pressure control solenoid "B" (SL2) circuit | Functioning normally |
| ECT (Engine coolant temperature) sensor circuit | Functioning normally |
| Knock sensor circuit | Functioning normally |
| ETCS (Electronic throttle control system) | System not down |
| Transmission shift position | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock sensor control | 0° CA or more |
| Engine | Starting |
| Transfer range | "High" *1 |
| Vehicle speed sensor "A" circuit | Functioning normally |
| Output speed sensor circuit | Functioning normally |
| Transfer output speed | 143 rpm or more |
| Transfer input speed/Transfer output speed | 0.9 to 1.1 |
| ECM selected gear | 1st |
| Vehicle speed | 1.2 to 24.9 mph (2 to 40 km/h) |
| Throttle valve opening angle | 6.5 % or more at engine speed of 2,000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 3rd |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| Throttle valve opening angle | 6.5 % or more at engine speed of 2,000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| Throttle valve opening angle | 6.5 % or more at engine speed of 2,000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 62.2 mph (100 km/h) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) (After transition from 4th to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition from 4th to 5th gear) | Less than 62.2 mph (100 km/h) |
| Turbine speed/Output speed | 3.30 to 7.50 (Actual gear is 1st) |
| Turbine speed/Output speed | 1.28 to 1.53 (Actual gear is 3rd) |
| Turbine speed/Output speed | 0.93 to 1.07 (Actual gear is 4th) |
| Turbine speed - Output speed x 4th gear ratio | 1,000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio | 1,000 rpm or more |
| Item | Test Details | Diagnostic Note |
| SHIFT | [Test Details] Operate the shift solenoid valve and set each shift position manually. [Vehicle Condition] Vehicle Speed: Less than 30 mph (50 km/h) [Others]
| Possible to check the operation of the shift solenoid valves. HINT: Shifting to the 5th gear is possible only when the vehicle is stationary with the engine idling. |
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th | 5th |
| Shift solenoid valve SL2 | ON | ON | ON | ON | OFF |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0776) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the intelligent tester main switch ON.
Select the items "DIAGNOSIS/ ENHANCED OBD II/ DTC INFO/ CURRENT CODES".
Read the DTCs using the intelligent tester.
| Display (DTC Output) | Proceed to |
| Only "P0776" is output | A |
| "P0776" and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LINE PRESS UP) |
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.
Follow the instructions on the tester and perform the ACTIVE TEST.
Measure the line pressure with SST.
| Item | Test Details | Diagnostic Note |
| LINE PRESS UP* | [Test Details] Operate shift solenoid SLT and raise line pressure. [Vehicle Condition]
| - |
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE SL2 |
![]() |
Remove the shift solenoid valve SL2.
Measure the resistance.
| Tester Connection | Specified Condition |
| 1 - 2 | 5.0 to 5.6 Ωat 20°C (68°F) |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (See chapter 2 in the problem symptoms table) |
|
| ||||
| OK | ||
| ||