Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0781    1-2 Shift (1-2 Shift Valve)

for Preparation Click here


DESCRIPTION

A093769E02
The 1-2 shift valve performs shifting to 1st gear and other gears.

DTC No.
DTC Detection Conditions
Trouble Areas
P0781
1-2 shift valve malfunction:
The ECM determines that there is a malfunction when the following conditions (a) and (b), or (a) and (c) are met (2-trip detection logic):
  1. (a) When the ECM directs the gearshift to switch to 2nd gear, the actual gear is shifted to 1st.
  2. (b) When the ECM directs the gearshift to switch to 4th gear, the actual gear is shifted to 3rd.
  3. (c) When the ECM directs the gearshift to switch to 5th gear, the engine overruns (clutch slips)
  1. Valve body is blocked up or stuck (1-2 shift valve)
  2. Shift solenoid valve SLT remains open or closed
  3. Automatic transmission (clutch, brake or gear, etc.)

HINT:
Gear positions in the event of a 1-2 shift valve mechanical problem:


Gearshift controlled by ECM
1st
2nd
3rd
4th
5th
Actual gear position under malfunction
1st
1st
3rd
3rd
N*
N*: Neutral

MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction of the spring compression. The ECM controls the gearshifts by turning the shift solenoid valves "ON/OFF" and switching oil pressure to the valves in the valve body.
The ECM calculates the "actual" transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift solenoids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear position and the commanded gear position are different, it will illuminate the MIL and store the DTC .

MONITOR STRATEGY


Related DTCs
P0781: Valve body/Rationality check
Required sensors/Components (Main)
Valve body
Required sensors/Components (Related)
Automatic transmission assembly, Speed sensor (NT), Speed sensor (SP2), Vehicle speed sensor, Throttle position sensor
Frequency of operation
Continuous
Duration
Conditions (A) and (B)
0.4 seconds
Condition (C)
3 seconds
Condition (D)
0.5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS

The following conditions are common to all Conditions (A), (B), (C) and (D).

The monitor will run whenever the following DTCs are not present.
P0115 - P0118: ECT sensor
P0125: Insufficient ECT for Closed Loop
P0500: VSS
P0748 - P0799: Trans Solenoid (range)
Turbine speed sensor (NT) circuit
Functioning normally
Output speed sensor (SP2) circuit
Functioning normally
Shift solenoid "A" (S1) circuit
Functioning normally
Shift solenoid "B" (S2) circuit
Functioning normally
Shift solenoid "E" (SR) circuit
Functioning normally
Pressure control solenoid "A" (SL1) circuit
Functioning normally
Pressure control solenoid "B" (SL2) circuit
Functioning normally
ECT (Engine coolant temperature) sensor circuit
Functioning normally
Knock sensor circuit
Functioning normally
ETCS (Electronic throttle control system)
System not down
Transmission shift position
"D"
ECT
40°C (104°F) or more
Spark advance from max. retard timing by knock sensor control
0°CA or more
Engine
Starting
Transfer range
"High" *1
*1: Following conditions are met

Vehicle speed sensor "A" circuit
Functioning normally
Output speed sensor circuit
Functioning normally
Transfer output speed
143 rpm or more
Transfer input speed/Transfer output speed
0.9 to 1.1

Condition (A) 
ECM selected gear
2nd
Vehicle speed
1.2 mph (2 km/h) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

Condition (B) 
ECM selected gear
4th
Vehicle speed
1.2 mph (2 km/h) or more
Throttle valve opening angle
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

Condition (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed
(During transition from 4th to 5th gear)
Less than 62.2 mph (100 km/h)

Condition (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed
After transition from 4th to 5th gear)
Less than 62.2 mph (100 km/h)

TYPICAL MALFUNCTION THRESHOLDS

Condition (A) and Conditions (B), (C) or (D) are met:

Condition (A) 
Turbine speed/Output speed
3.30 to 7.50
(Actual gear is 1st)

Condition (B) 
Turbine speed/Output speed
1.28 to 1.53
(Actual gear is 3rd)

Condition (C) 
Turbine speed - Output speed x 4th gear ratio
1,000 rpm or more

Condition (D) 
Turbine speed - Output speed x 5th gear ratio
1,000 rpm or more

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the main switch ON.

  1. Select the items "DIAGNOSIS/ ENHANCED OBD II/ DTC INFO/ CURRENT CODES".

  1. Read the DTCs using the intelligent tester.

    Result: 
    Display (DTC Output)
    Proceed to
    Only "P0781" is output
    A
    "P0781" and other DTCs
    B

    HINT:
    If any codes besides "P0781" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT)

HINT:
Performing the ACTIVE TEST using the intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the ACTIVE TEST as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
  4. Turn the ignition switch to the ON position.
  5. Push the "ON" button of the tester.
  6. Clear the DTC.
  7. Select the items "DIAGNOSIS/ ENHANCED OBD II/ ACTIVE TEST/ SHIFT".
  8. According to the display on the tester, perform the "ACTIVE TEST".

HINT:
While driving, the shift position can be changed with the intelligent tester.
Comparing the shift position directed by the ACTIVE TEST with the actual shift position enables the problem to be confirmed (Click here).


Item
Test Details
Diagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position manually.
[Vehicle Condition]
Vehicle Speed: Less than 30 mph (50 km/h)
[Others]
  1. Press →button: Shift up
  2. Press ←button: Shift down
Possible to check the operation of the shift solenoid valves.
HINT:
Shifting to the 5th gear is possible only when the vehicle is stationary with the engine idling.

HINT:
  1. This test can be conducted when the vehicle speed is 30 mph (50 km/h) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the DATA LIST/ SHIFT display on the intelligent tester.
  6. Gear positions in the event of a solenoid valve mechanical problem:

    Gearshift operated by tester
    1st
    2nd
    3rd
    4th
    5th
    Actual gear position under malfunction
    1st
    1st
    3rd
    3rd
    N*
    N*: Neutral

    OK:
    Gear position changes in accordance with the tester operation.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LINE PRESS UP)
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time.
The DATA LIST can be displayed during the ACTIVE TEST.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the intelligent tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.

  1. Follow the instructions on the tester and perform the ACTIVE TEST.

  1. Measure the line pressure with SST.

    Item
    Test Details
    Diagnostic Note
    LINE PRESS UP*
    [Test Details]
    Operate shift solenoid SLT and raise line pressure.
    [Vehicle Condition]
    1. Vehicle stopped
    2. IDL: ON

    HINT:
    OFF: Line pressure up (when Active Test of "LINE PRESS UP" is performed, ECM commands SLT solenoid to turn OFF)
    ON: No action (normal operation)

    -
    *: "LINE PRESS UP" in the ACTIVE TEST is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well. Please note that the pressure values in the ACTIVE TEST and HYDRAULIC TEST are different.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


4.CLEAR DTC AND PERFORM RUNNING TEST
  1. Clear the DTC, and check for the DTC again after conducting the "MONITOR DRIVE PATTERN FOR ECT TEST" (Click here).

    OK:
    No DTC



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

END