Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1235/35    Foreign Object is Attached on Tip of Front Speed Sensor RH

DTC    C1236/36    Foreign Object is Attached on Tip of Front Speed Sensor LH

DTC    C1238/38    Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC    C1239/39    Foreign Object is Attached on Tip of Rear Speed Sensor LH

for Preparation Click here


DESCRIPTION

The Skid Control ECU sets this DTC if, according to abnormal signals input by the sensor, it detects that foreign material is adhering to the speed sensor tip or the sensor rotor, or the rotor has any missing teeth.
This DTC may be set if parts such as the speed sensor circuit connector or wire harness are malfunctioning.

DTC No.
DTC Detecting Conditions
Trouble Areas
C1235/35
C1236/36
C1238/38
C1239/39
  1. At vehicle speed of 12 mph (20 km/h) or more, noise in speed sensor signal continues for 5 seconds or more.
  2. At vehicle speed of 6 mph (10 km/h) or more, noise detected as rotor turns, for 15 seconds or more.
  1. Master cylinder solenoid (skid control ECU)
  2. Speed sensor
  3. Speed sensor rotor

HINT:
DTC C1235/35 relates to the front right speed sensor.
DTC C1236/36 relates to the front left speed sensor.
DTC C1238/38 relates to the rear right speed sensor.
DTC C1239/39 relates to the rear left speed sensor.


WIRING DIAGRAM


C124740E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SPEED SENSOR)


    F052318E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the speed sensor connectors.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    S1-10 (FL+) - S3-2 (FL+)
    Below 1 Ω
    S1-9 (FL-) - S3-1 (FL-)
    Below 1 Ω
    S1-40 (FR+) - S4-2 (FR+)
    Below 1 Ω
    S1-39 (FR-) - S4-1 (FR-)
    Below 1 Ω
    S1-15 (RL+) - S22-2 (RL+)
    Below 1 Ω
    S1-16 (RL-) - S22-1 (RL-)
    Below 1 Ω
    S1-44 (RR+) - S22-4 (RR+)
    Below 1 Ω
    S1-45 (RR-) - S22-3 (RR-)
    Below 1 Ω

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    S1-10 (FL+) - Body ground
    10 kΩ or higher
    S1-9 (FL-) - Body ground
    10 kΩ or higher
    S1-40 (FR+) - Body ground
    10 kΩ or higher
    S1-39 (FR-) - Body ground
    10 kΩ or higher
    S1-15 (RL+) - Body ground
    10 kΩ or higher
    S1-16 (RL-) - Body ground
    10 kΩ or higher
    S1-44 (RR+) - Body ground
    10 kΩ or higher
    S1-45 (RR-) - Body ground
    10 kΩ or higher

  1. Reconnect the speed sensor connectors.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT MASTER CYLINDER SOLENOID (TERMINAL VOLTAGE)


    F052319E02
  1. Disconnect the speed sensor connectors.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    S3-2 (FL+) - Body ground
    7.5 to 12 V
    S4-2 (FR+) - Body ground
    7.5 to 12 V
    S22-2 (RL+) - Body ground
    7.5 to 12 V
    S22-4 (RR+) - Body ground
    7.5 to 12 V

  1. Turn the ignition switch to OFF.

  1. Reconnect the speed sensor connectors.



NG
REPLACE MASTER CYLINDER SOLENOID
OK


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
A


4.INSPECT SPEED SENSOR
  1. Remove the speed sensor (Click here or Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE SPEED SENSOR
OK

CLEAN OR REPLACE SPEED SENSOR