Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C1248/48    Open Circuit in Rear Differential Lock

for Preparation Click here


DESCRIPTION

The 4WD control ECU stimulates the actuator to lock the rear differential in accordance with the rear diff. lock switch. The skid control ECU monitors the transfer indicator switch (rear diff. lock ) and if the rear differential is locked, at which time the rear diff. lock indicator light is illuminated, prohibits ABS control. At the same time, the skid control ECU illuminates the ABS warning light.

DTC No.
DTC Detecting Condition
Trouble Areas
C1248/48
At vehicle speed of 31 mph (50 km/h) or more, 3 seconds or more elapse after rear differential changes from free to lock.
  1. Transfer indicator switch (rear diff. lock)
  2. Rear differential lock circuit
  3. Brake actuator (skid control ECU)
  4. 4WD control ECU

WIRING DIAGRAM


C124745E01


INSPECTION PROCEDURE

1.INSPECT SKID CONTROL ECU (EXI2 TERMINAL VOLTAGE)


    C121700E05
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

  1. Check the rear diff. lock indicator light.

    Standard:

    Terminal Connection
    Vehicle Condition
    Specified Condition
    Rear Diff. Indicator Light
    S1-7 (EXI2) - Body ground
    Rear Differential free
    8 to 14 V
    OFF
    S1-7 (EXI2) - Body ground
    Rear Differential locked
    1.5 V
    ON

  1. Turn the ignition switch to OFF.

  1. Reconnect the skid control ECU connector.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of 31 mph (50 km/h) or more for 3 seconds or more with the rear differential free.

  1. Check if the same DTCs are detected.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR 

3.INSPECT TRANSFER INDICATOR SWITCH (REAR DIFF. LOCK)


    F052057E01
  1. Disconnect the transfer indicator switch connector.

  1. Remove the transfer indicator switch.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Push
    Below 1 Ω
    1 - 2
    Free
    10 kΩ or higher

  1. Reinstall the transfer indicator switch.

  1. Reconnect the transfer indicator switch connector.



NG
REPLACE TRANSFER INDICATOR SWITCH
OK


4.CHECK HARNESS AND CONNECTOR


    F052348E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the 4WD control ECU connector.

  1. Disconnect the transfer indicator switch connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    T14-2 - Body ground
    8 to 14 V

  1. Turn the ignition switch to OFF.

  1. Reconnect the transfer indicator switch connector.

  1. Reconnect the 4WD control ECU connector.

  1. Reconnect the skid control ECU connector.



OK
REPLACE 4WD CONTROL ECU
NG


5.CHECK HARNESS AND CONNECTOR


    F052348E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the 4WD control ECU connector.

  1. Disconnect the transfer indicator switch connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    T14-2 - Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the transfer indicator switch connector.

  1. Reconnect the 4WD control ECU connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER