Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING VALVE AND TRANSMITTER

TIRE PRESSURE WARNING VALVE AND TRANSMITTER > INSTALLATION

for Preparation Click here



1. INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER


C117509E01
  1. Insert the tire pressure warning valve and transmitter into the valve installation hole. Insert it from the inside of the rim so that the print surface can be seen.

    NOTICE:
    1. Check that there is no visible deformation, damage or other abnormalities in the transmitter.
    2. Check that there is no foreign matter on the inner grommet and around the rim hole.
    3. If installed in the reverse direction, the tire pressure warning valve and transmitter may be damaged or fail to transmit signals when running at high speed.
    4. If installing a new tire pressure warning valve and transmitter, write down the ID number before installation.
    5. It is necessary to register the ID in the ECU after installation (Click here).



    C117510E01
  1. Install the washer onto the tire pressure warning valve and transmitter from the rim side and tighten it with the nut.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    NOTICE:
    1. The specified torque only applies the first time washer is used.
    2. Check that there is no foreign matter on the washer or nut.
    3. If the tire pressure warning valve and transmitter is removed when the tire is removed for replacement, check that there is no damage or cuts, and no foreign matter such as mud, dirt or sand attached to the grommet. Replace the grommet with a new one if necessary.
    4. Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, washer and nut. Failing to check may result in improper installation.

  1. After the tire is inflated, the valve nut may be loose. Retighten the nut to the specified torque and then check for air leaks with soapy water.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    NOTICE:
    The specified torque only applies the first time washer is used.



    C084539E01
  1. Set the wheel disc to the mounting machine and install the lower tire bead. Position the main body of the valve sensor in the shaded area shown in the illustration.

    NOTICE:
    If the valve sensor is positioned outside this area, it generates interference with the tire bead, causing possible damage to the valve sensor.

  1. Install the upper bead.

    NOTICE:
    Make sure that the tire bead and tool do not interfere with the main body of the valve sensor and that the valve sensor is not interfered with the bead.



2. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



3. INSTALL REAR WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



4. INSTALL SPARE TIRE


5. REGISTER TRANSMITTER ID

NOTICE:
  1. Register the transmitter IDs after the tire pressure warning ECU or the tire pressure warning valve and transmitters have been replaced.

  2. F100115E02
    If the transmitter IDs cannot be registered, the tire pressure warning ECU is probably in initialization mode. Initialization mode can be terminated by making a short circuit between terminals TC and CG of the DLC3 connector.
  3. In order to avoid damage to the tire pressure warning valve and transmitters, observe the instructions when removing and installing the tire pressure warning valve and transmitters.



    C124986E01
  1. Prepare the all transmitter ID data before starting registration.

    HINT:
    1. Read the registered transmitter IDs that are stored in the ECU using the intelligent tester and note them down.
    2. If reading stored transmitter IDs is impossible due to malfunctions of components such as the tire pressure warning antenna and receiver, remove the tires from the wheels and check the IDs located on the tire pressure warning valves and transmitters (Click here ).
    3. When replacing the tire pressure warning valves and transmitters, note down the IDs written on the tire pressure warning valves and transmitters.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.



  1. Select the REGIST TIRE by following the prompts displayed on the intelligent tester screen (UTILITY - REGIST TIRE).


    C122895E01

    NOTICE:
    1. The previously registered IDs will be deleted from the memory when the registration is completed.
    2. If the procedures of the registration are not completed within 5 minutes, the mode returns to normal operation mode.
    3. When the system is in initialization mode after the reset switch has been operated, the registration is disabled until the initialization process is canceled or completed.



    C122889E01
  1. Input the IDs (ID1 to ID5) using the intelligent tester and transmit them to the tire pressure warning ECU.



    C122894
  1. When the ID transmission has successfully been completed, the message shown in the illustration appears on the tester screen.

  1. Turn the ignition switch to the OFF position, and then turn to the ON position.

  1. Select "SIGNAL CHECK" on the intelligent tester (Click here ).

  1. Confirm that the transmitter IDs and the data of tire pressure of all the tires are displayed on the intelligent tester screen.

    Item
    Measurement Item/
    Range (Display)
    Normal Condition
    REGIT ID1 CODE
    Registered ID1 code/
    minimum: 0
    maximum: FFFFFFF
    ID No. of registered transmitter ID1 displayed
    REGIT ID2 CODE
    Registered ID2 code/
    minimum: 0
    maximum: FFFFFFF
    ID No. of registered transmitter ID2 displayed
    REGIT ID3 CODE
    Registered ID3 code/
    minimum: 0
    maximum: FFFFFFF
    ID No. of registered transmitter ID3 displayed
    REGIT ID4 CODE
    Registered ID4 code/
    minimum: 0
    maximum: FFFFFFF
    ID No. of registered transmitter ID4 displayed
    REGIT ID5 CODE
    Registered ID5 code/
    minimum: 0
    maximum: FFFFFFF
    ID No. of registered transmitter ID5 displayed
    TIREPRESS1
    ID1 tire pressure/
    minimum: 0 kPa (0 kgf/cm2, 0 psi)
    maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    TIREPRESS2
    ID2 tire pressure/
    minimum: 0 kPa (0 kgf/cm2, 0 psi)
    maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    TIREPRESS3
    ID3 tire pressure/
    minimum: 0 kPa (0 kgf/cm2, 0 psi)
    maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    TIREPRESS4
    ID4 tire pressure/
    minimum: 0 kPa (0 kgf/cm2, 0 psi)
    maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    TIREPRESS5
    ID5 tire pressure/
    minimum: 0 kPa (0 kgf/cm2, 0 psi)
    maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure

    NOTICE:
    1. It may take up to 1 minute to update the tire pressure data.
    2. If the IDs have not been registered, DTC C2171/71 is set in the tire pressure warning ECU after approximately 30 minutes.

  1. Disconnect the intelligent tester with the ignition switch turned OFF.



6. INSPECT TIRE PRESSURE WARNING SYSTEM
(Click here)