Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the Techstream, read the "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed:
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicator on speedometer
    Engine Speed
    Engine speed:
    Min.: 0 rpm, Max.: 16383.75 rpm
    600 to 700 rpm: Idling, engine warmed up, no load
    -
    Calculate Load
    Calculated load by ECM:
    Min.: 0%, Max.: 100%
    1. 11 to 26%: Idling
    2. 12 to 27%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load:
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    Load percentage in terms of maximum intake air flow amount
    MAF
    Air flow rate from Mass Air Flow meter:
    Min.: 0 gm/sec, Max.: 655.35 gm/sec
    2.0 to 4.5 gm/sec: Idling
    If value approximately 0.0 gm/sec:
    1. MAF meter power source circuit open
    2. VG circuit open or short
    If value 160.0 gm/sec or more:
    1. E2G circuit open
    Atmosphere Pressure
    Atmospheric pressure:
    Min.: 0 kPa(abs) [0 mmHg(abs)], Max.: 255 kPa(abs) [1912.6 mmHg(abs)]
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature:
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (167 to 212°F): After warming up
    1. If value -40°C (-40°F): sensor circuit open
    2. If value higher than 135°C (275°F): sensor circuit shorted
    Intake Air
    Intake air temperature:
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    Equivalent to ambient air temperature
    1. If value -40°C (-40°F): sensor circuit open
    2. If value higher than 128°C (262°F): sensor circuit shorted
    Engine Run Time
    Engine run time:
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data
    Initial Engine Coolant Temp
    Initial engine coolant temperature:
    Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
    Engine coolant temperature when engine started
    Service data
    Initial Intake Air Temp
    Initial intake air temperature:
    Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
    Intake air temperature when engine started
    Service data
    Battery Voltage
    Battery voltage:
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accelerator Position
    Accelerator pedal position:
    Min.: 0%, Max.: 399.9%
    Actual accelerator pedal position
    -
    Accel Sens. No.1 Volt %
    Accelerator pedal position No. 1:
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 54 to 86%: Accelerator pedal fully depressed
    -
    Accel Sens. No.2 Volt %
    Accelerator pedal position No. 2:
    Min.: 0%, Max.: 100%
    1. 12 to 42%: Accelerator pedal released
    2. 66 to 98%: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.1
    Accelerator pedal position sensor No. 1 voltage:
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 2.6 to 4.5 V: Accelerator pedal fully depressed
    ETCS service data
    Accel Sensor Out No.2
    Accelerator pedal position sensor No. 2 voltage:
    Min.: 0 V, Max.: 4.98 V
    1. 1.2 to 2.0 V: Accelerator pedal released
    2. 3.4 to 5.0 V: Accelerator pedal fully depressed
    ETCS service data
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle:
    ON or OFF
    ON: Idling
    -
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1:
    Min.: 0 deg, Max.: 124.5 deg.
    2.5 to 23.75 deg: after learning
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2:
    Min.: 0 deg., Max.: 124.5 deg.
    32.5 to 53.75 deg: after learning
    ETCS service data
    Throttle Sensor Volt %
    Throttle valve opening percentage according to throttle position sensor:
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA1
    Throttle Sensor #2 Volt %
    Throttle position No. 2 sensor:
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Accelerator pedal released
    2. 92 to 100%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA2
    ST1
    Brake pedal signal:
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard:
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction:
    ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle:
    ON or OFF
    1. ON: Accelerator pedal released
    2. OFF: Accelerator pedal fully depressed
    -
    Throttle Require Position
    Required throttle position:
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Idling
    -
    Throttle Sensor Position*1
    Throttle position sensor:
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 50 to 80%: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on ECM
    Throttle Position No.1
    Throttle position No. 1 output voltage:
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 3.2 to 4.8 V: Accelerator pedal fully depressed
    3. 0.6 to 1.4 V: Fail-safe operating
    ETCS service data
    Throttle Position No.2
    Throttle position No. 2 output voltage:
    Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Accelerator pedal released
    2. 4.6 to 5.0 V: Accelerator pedal fully depressed
    3. 2.1 to 3.1 V: Fail-safe operating
    ETCS service data
    Throttle Position Command
    Throttle position command value:
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    -
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1:
    Min.: 0 V, Max.: 4.98 V
    0.6 to 1.4 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2:
    Min.: 0 V, Max.: 4.98 V
    1.7 to 2.5 V
    ETCS service data
    Throttle Motor Current
    Throttle actuator current:
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    ETCS service data
    Throttle Motor DUTY
    Throttle actuator:
    Min.: 0%, Max.: 100%
    10 to 22%: Idling after engine warmed up
    ETCS service data
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open):
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (close):
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value):
    Min.: 0 V, Max.: 4.98 V
    0.4 to 1.0 V: Accelerator pedal released
    -
    +BM Voltage
    +BM voltage:
    Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Ignition switch ON and system normal
    ETCS service data
    Actuator Power Supply
    Actuator power supply:
    ON or OFF
    ON: Idling
    ETCS service data
    Throttle Position
    Throttle valve opening angle:
    Min.: 0 deg, Max.: 499.99 deg
    0 to 84 deg
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    ISC Flow
    Flow rate calculated from information from each sensor:
    Min.: 0 L/s, Max.: 79.99 L/s
    0 to 40 L/s: Idling
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    ISC Position
    Target valve opening angle calculated from ISC control:
    Min.: 0 deg, Max.: 499.99 deg
    0 to 21 deg: Idling
    Check the value when the engine stalls, is difficult to start, or idles roughly.
    This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
    ISC Feedback Value
    ISC feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    ISC Learning Value
    ISC learning value:
    Min.: -40 L/s, Max.: 39.99 L/s
    0.5 to 6.4 L/s
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Electric Load Feedback Val
    Electrical load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Air Conditioner FB Val
    Air conditioner load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    PS Feedback Val
    Power steering load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Low Revolution Control
    Status of low engine speed control:
    ON or OFF
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    N Range Status
    Shift lever N status:
    ON or OFF
    -
    For automatic transmission models
    Injector (Port)
    Injection period of No. 1 cylinder:
    Min.: 0 μs, Max.: 65535 μs
    1000 to 3000 μs: Idling
    -
    Injection Volum (Cylinder1)
    Injection volume (Cylinder 1):
    Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml: Idling
    Quantity of fuel injection volume for 10 times
    Fuel Pump/Speed Status
    Fuel pump/Speed status:
    ON or OFF
    -
    -
    Vacuum Pump
    Key-off EVAP system leak detection pump status:
    ON or OFF
    -
    -
    EVAP (Purge) VSV
    EVAP (Purge) VSV control duty:
    Min.: 0%, Max.: 100%
    0 to 100%: Idling, under purge control
    Order signal from ECM
    Evap Purge Flow
    Ratio of evaporative purge flow to intake air volume:
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density:
    Min.: -200%, Max.: 199.993%
    -40% to 0%: Idling
    Service data
    Vapor Pressure Pump
    Vapor pressure:
    Min.: 0 kPa(abs) [0 mmHg(abs)], Max.: 1441.770 kPa(abs) [10814.16 mmHg(abs)]
    Nearly atmospheric pressure: Fuel tank cap removed
    EVAP system pressure monitored by canister pressure sensor
    Vapor Pressure (Calculated)
    Vapor pressure (calculated):
    Min.:-720.896 kPa(abs) [-5407 mmHg(abs)], Max.: 720.874 kPa(abs) [5407 mmHg(abs)]
    Nearly atmospheric pressure: Fuel tank cap removed
    EVAP system pressure monitored by canister pressure sensor
    EVAP System Vent Valve
    Key-off EVAP system vent valve status:
    ON or OFF
    -
    -
    EVAP Purge VSV
    VSV status for EVAP control:
    ON or OFF
    -
    -
    Purge Cut VSV Duty
    Purge VSV duty:
    Min.: 0%, Max.: 399.9%
    -
    -
    Target Air-Fuel Ratio
    Ratio compared to stoichiometric level:
    Min.: 0, Max.: 1.99
    0.8 to 1.2: Idling
    -
    AF Lambda B1S1
    Short-term fuel trim associated with bank 1 sensor 1:
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air-fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    A/F sensor output voltage for bank 1 sensor 1:
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling, engine warmed up
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    AFS Current B1S1
    Air fuel ratio sensor output current for bank 1 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling, engine warmed up
    Value becomes higher when fuel cut executed under high engine speed
    A/F Heater Duty #1
    A/F heater duty ratio (for Bank 1):
    Min.: 0%, Max.: 399.9%
    0 to 100%
    -
    O2S B1S2
    Heated oxygen sensor output voltage for bank 1 sensor 2:
    Min.: 0 V, Max.: 1.275 V
    0.0 to 0.9 V: Driving at 70 km/h (44 mph)
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    O2S Impedance B1S2
    Sub heated oxygen sensor impedance (bank 1 sensor 2):
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm: After driving for 10 minutes or more in urban area
    -
    O2 Heater B1S2
    Heated oxygen sensor heater (for Bank 1 Sensor 2)
    Not Act or Active
    -
    -
    O2 Heater Curr Val B1S2
    Heated oxygen sensor current (for Bank 1 Sensor 2):
    Min.: 0 A, Max.: 4.999 A
    -
    -
    Short FT #1
    Short-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%
    -15 to 15%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%
    -15 to 15%
    Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
    Total FT #1
    Total fuel trim of bank 1:
    Min.: -0.5, Max.: 0.496
    -0.28 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (bank 1):
    OL or CL or OLDrive or OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
    3. OLDrive: Open loop due to driving conditions (fuel enrichment)
    4. OLFault: Open loop due to detected system fault
    5. CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, is malfunctioning
    Air Pump Pressure (Absolute)
    Air pump pressure (absolute):
    Min.: 0 kPa (0 mmHg), Max.: 65535 kPa (491553.1 mmHg)
    Atmospheric pressure +2.5 kPa (18.751 mmHg) or more: Air pump ON.
    Air switching valve open
    Close to atmospheric pressure: Air pump OFF, Air switching valve close
    -
    Air Pump Pulsation Pressure
    Air pump pulsation pressure:
    Min.: 0 kPa (0 mmHg), Max.: 655.35 kPa (4915.531 mmHg)
    -
    Cumulative pulsation pressure calculated by ECM
    Secondary Air Control VSV
    Secondary air injection system status:
    ON or OFF
    ON: Secondary air injection system operating
    -
    2nd Air System Status
    Secondary air system status:
    ON or OFF
    ON: Secondary air system operating
    -
    AI Test
    AI operation prohibition:
    READY or NOT RDY
    READY
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder:
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 4 to 17 deg: Idling
    -
    Knock Feedback Value
    Feedback value of knocking:
    Min.: -1024°CA, Max.: 1023.9°CA
    -19 to 0°CA: Driving at 70 km/h (44 mph)
    -
    Knock Correct Learn Value
    Correction learning value of knocking:
    Min.: -1024°CA, Max.: 1023.9°CA
    -19 to 0°CA: Driving at 70 km/h (44 mph)
    -
    Idle Spark Advn Ctrl #1
    Ignition timing advance value (for No. 1 cylinder):
    Min.: 0° CA, Max.: 15.93° CA
    3 to 13°CA: Idling
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #2
    Ignition timing advance value (for No. 2 cylinder):
    Min.: 0° CA, Max.: 15.93° CA
    3 to 13°CA: Idling
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #3
    Ignition timing advance value (for No. 3 cylinder):
    Min.: 0° CA, Max.: 15.93° CA
    3 to 13°CA: Idling
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #4
    Ignition timing advance value (for No. 4 cylinder):
    Min.: 0° CA, Max.: 15.93° CA
    3 to 13°CA: Idling
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    VVT Control Status #1*2
    VVT control (bank 1) status:
    ON or OFF
    -
    Active Test support data
    VVT Advance Fail
    VVT control failure status:
    ON or OFF
    ON: VVT control failure
    -
    VVT Aim Angle #1*2
    VVT aim angle (bank 1):
    Min.: 0%, Max.: 399.9%
    0%: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle #1*2
    VVT change angle (bank 1):
    Min.: 0 degFR, Max.: 639.9 degFR
    0 to 56 degFR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #1*2
    VVT OCV operation duty:
    Min.: 0%, Max.: 399.9%
    0 to 67%: Idling
    Requested duty value for intrusive operation
    Catalyst Temp B1S1
    Catalyst temperature (associated sensor 1):
    Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    Close to catalyst inlet temperature
    -
    Catalyst Temp B1S2
    Catalyst temperature (associated sensor 2):
    Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    Close to catalyst inlet temperature
    -
    Starter Signal
    Starter signal (STA terminal input status):
    ON or OFF
    ON: Cranking
    -
    Power Steering Signal
    Power steering signal:
    ON or OFF
    ON: Power steering operation
    -
    Neutral Position SW Signal
    Park/neutral position switch status:
    ON or OFF
    ON: Shift lever in P or N
    For automatic transmission models
    Clutch Switch
    Clutch Switch:
    ON or OFF
    ON: Clutch pedal depressed
    For manual transmission models
    4WD SW
    4WD switch
    ON or OFF
    ON: 4WD ON
    For 4WD models
    Transfer L4
    Transfer L4 switch
    ON or OFF
    ON: Transfer L4 ON
    For 4WD models
    For automatic transmission models
    Stop Light Switch
    Stop light switch status:
    ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C switch status:
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch:
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel-cut condition:
    ON or OFF
    ON: Any fuel-cut operation executed
    -
    Immobiliser Communication
    Immobiliser communication:
    ON or OFF
    -
    OFF: Communication malfunctioning, or engine immobiliser system set
    ON: Communication normal
    Check Mode
    Check mode:
    ON or OFF
    ON: Check mode ON
    -
    SPD Test Result
    Check mode result for vehicle speed sensor:
    Compl or Incmpl
    -
    -
    AS Test Result
    Check mode result for secondary air injection system:
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor:
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (bank 1):
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (bank 1):
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor:
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor:
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor:
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor:
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor:
    Compl or Incmpl
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor:
    Not Avl or Avail
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor:
    Compl or Incmpl
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) monitor:
    Not Avl or Avail
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) monitor:
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C monitor:
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C monitor:
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor:
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor:
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor:
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor:
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor:
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor:
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor:
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor:
    Compl or Incmpl
    -
    -
    Component Monitor ENA
    Comprehensive component monitor:
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive component monitor:
    Compl or Incmpl
    -
    -
    Fuel System Monitor ENA
    Fuel system monitor:
    Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel system monitor:
    Compl or Incmpl
    -
    -
    Misfire Monitor ENA
    Misfire monitor:
    Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire monitor:
    Compl or Incmpl
    -
    -
    EGR/VVT Monitor ENA
    EGR monitor:
    Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR monitor:
    Compl or Incmpl
    -
    -
    Heater Monitor ENA
    O2S (A/FS) heater monitor:
    Unable or Enable
    -
    -
    Heater Monitor CMPL
    O2S (A/FS) heater monitor:
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor ENA
    O2S (A/FS) monitor:
    Unable or Enable
    -
    -
    O2S(A/FS) Monitor CMPL
    O2S (A/FS) monitor:
    Compl or Incmpl
    -
    -
    A/C Monitor ENA
    A/C monitor:
    Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C monitor:
    Compl or Incmpl
    -
    -
    2nd Air Monitor ENA
    2nd air monitor:
    Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd air monitor:
    Compl or Incmpl
    -
    -
    EVAP Monitor ENA
    EVAP monitor:
    Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP monitor:
    Compl or Incmpl
    -
    -
    Heated Cat Monitor ENA
    Heated catalyst monitor:
    Unable or Enable
    -
    -
    Heated Cat Monitor CMPL
    Heated catalyst monitor:
    Compl or Incmpl
    -
    -
    Catalyst Monitor ENA
    Catalyst monitor:
    Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst monitor:
    Compl or Incmpl
    -
    -
    TC Terminal
    TC terminal status:
    ON or OFF
    -
    -
    # Codes (Include History)
    Number of codes:
    Min.: 0, Max.: 255
    0: No emission related DTC detected
    -
    MIL
    MIL status:
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    Distance traveled since MIL turned ON:
    Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
    Distance since DTC detected
    -
    Running Time from MIL ON
    Running time since MIL turned ON:
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time since MIL turned ON
    -
    Time after DTC Cleared
    Time since DTCs cleared:
    Min.: 0 min., Max.: 65535 min.
    Equivalent to time since DTCs erased
    -
    Distance from DTC Cleared
    Distance traveled since DTCs cleared:
    Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
    Equivalent to distance driven since DTCs erased
    -
    Warmup Cycle Cleared DTC
    Warm-up cycles since DTCs cleared:
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles since DTCs cleared
    Dist Batt Cable Disconnect
    Distance after battery cable disconnected:
    Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
    Total distance vehicle driven after battery cable disconnected
    -
    IG OFF Elapsed Time
    Time after ignition switch off:
    Min.: 0 min, Max.: 655350 min
    Cumulative time after ignition switch off
    -
    OBD Requirements
    OBD requirement:
    OBD2 (California OBD)
    -
    Number of Emission DTC
    Emission related DTCs
    Min.: 0, Max.: 127
    -
    Number of emission related DTCs
    TC and TE1
    TC and CG (TE1) terminals of DLC3:
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter to calculated misfire rate:
    Min.: 0, Max.: 65535
    0 to 400
    -
    Cylinder #1 Misfire Count
    Misfire counter of cylinder 1:
    Min.: 0, Max.: 255
    0
    -
    Cylinder #2 Misfire Count
    Misfire counter of cylinder 2:
    Min.: 0, Max.: 255
    0
    -
    Cylinder #3 Misfire Count
    Misfire counter of cylinder 3:
    Min.: 0, Max.: 255
    0
    -
    Cylinder #4 Misfire Count
    Misfire counter of cylinder 4:
    Min.: 0, Max.: 255
    0
    -
    All Cylinders Misfire Count
    All cylinders misfire counter:
    Min.: 0, Max.: 255
    0
    -
    Misfire RPM
    Average of engine speed when misfire occurs:
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Average of engine load when misfire occurred:
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Average of engine load when misfire occurred:
    Min.: -128%, Max.: 127%
    -100 to 99.2%
    When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. Misfire margin is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring. A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring
    Catalyst OT MF F/C
    Catalyst overheat misfire prevention fuel cut function availability:
    Not Avl or Avail
    1. Avail: Catalyst overheat misfire prevention fuel cut function available
    2. Not Avl: Catalyst overheat misfire prevention fuel cut function not available
    Service data
    Cat OT MF F/C History
    Catalyst overheat misfire prevention fuel cut function history:
    ON or OFF
    OFF: Fuel cut operation No history of fuel cut operation
    Service data
    Cat OT MF F/C Cylinder #1
    Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #2
    Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #3
    Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #4
    Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Engine Speed (Starter Off)
    Engine speed when starter off:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Starter Count
    Number of times starter turned on after ignition switch turned from off to ON:
    Min.: 0, Max.: 255
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Run Dist of Previous Trip
    Distance traveled during previous trip:
    Min.: 0 km (0 mile), Max.: 655.35 km (407.23 mile)
    -
    Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
    After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

    HINT:
    Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

    Engine Starting Time
    Engine run time (elapsed time from ignition switch ON to off):
    Min.: 0 ms, Max.: 655350 ms
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Coolant Temp
    Coolant temperature of previous trip:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Intake Temp
    Intake air Coolant temperature of previous trip:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Engine Oil Temperature
    Engine oil temperature (estimated):
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Eng Oil Temp
    Engine oil temperature of previous trip (estimated):
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Ambient Temp for A/C
    Ambient temperature:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Ambient Temp
    Ambient temperature of previous trip:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Engine Start Hesitation
    History of instances of slow engine starts:
    ON or OFF
    -
    -
    Low Rev for Eng Start
    History of low engine speed after engine starts:
    ON or OFF
    -
    -
    Minimum Engine Speed
    Minimum engine speed:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Reference:
    When the engine stalls, is difficult to start, or idles roughly
    Fuel Cut Elps Time
    Elapsed time since Fuel Cut due to high engine speed
    Min.: 0 sec, Max.: 68746 sec
    -
    The time elapsed after high engine rotation speed has occurred (More than the rpm at which fuel cut occurs + 500rpm).
    ACT VSV
    A/C cut status for Active Test:
    ON or OFF
    -
    -
    Brake Override System
    Brake override system status/
    ON or OFF
    ON: Brake override system operating
    -
    Idle Fuel Cut
    Fuel cut idle:
    ON or OFF
    ON: Fuel cut operating
    Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
    FC TAU
    Fuel cut TAU (Fuel cut during very light load):
    ON or OFF
    ON: Fuel cut operating
    Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
    Immobiliser Fuel Cut
    Status of the immobiliser fuel cut:
    ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of the immobiliser fuel cut history:
    ON or OFF
    -
    -
    Electrical Load Signal 1
    Electrical load signal (ELS1 terminal input):
    ON or OFF
    ON: Tail light switch ON
    -
    Electrical Load Signal 2
    Electrical load signal (ELS2 terminal input):
    ON or OFF
    ON: Voltage inverter switch ON
    -
    Model Code
    Model code
    -
    Identifying model code: TRN2###
    System Identification
    System identification
    -
    Used for identifying the engine system: Gasoline (gasoline engine)
    Engine Type
    Engine type
    -
    Identifying engine type: 2TRFE
    Cylinder Number
    Cylinder number:
    Min.: 0, Max.: 255
    -
    Identifying cylinder number: 4
    Transmission Type
    Transmission type
    -
    Identifying the transmission type: MT or ECT.
    Destination
    Destination
    -
    Identifying destination: A (America)
    Model Year
    Model year
    -
    Identifying model year: 20##
    Engine Speed of Cyl #1
    Engine RPM for cylinder 1:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199.2187 rpm: Not performed using Active Test
    Engine Speed of Cyl #2
    Engine RPM for cylinder 2:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199.2187 rpm: Not performed using Active Test
    Engine Speed of Cyl #3
    Engine RPM for cylinder 3:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199.2187 rpm: Not performed using Active Test
    Engine Speed of Cyl #4
    Engine RPM for cylinder 4:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199.2187 rpm: Not performed using Active Test
    Av Engine Speed of All Cyl
    Engine RPM for all cylinders:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199.2187 rpm: Not performed using Active Test
    SPD (SP2)
    Output shaft speed:
    Min.: 0 km/h, Max.: 255 km/h
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
    For automatic transmission models
    Lock Up
    Lock-up
    ON or OFF
    ON: Lock up operating
    For automatic transmission models

    HINT:
    1. *1: Excluding throttle valve opening percentage due to idle speed control.
    2. *2: Data List values are only displayed when performing the following Active Test: Control the VVT System (Bank 1), Control the VVT Linear (Bank 1). For other Active Test, the Data List value will be 0.


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the "Active Test".

    Tester Display
    Test Part
    Control Range
    Diagnostic Notes
    Control the Injection Volume
    Change injection volume
    -12.5 to 24.8%
    1. All injectors tested at the same time
    2. Perform test at less than 3000 rpm
    3. Perform the test at the engine speed 3000 rpm or less and engine coolant temperature 80°C (176°F) or more.
    4. Enrichment for over temperature protection off.
    5. Injection volume can be changed in fine gradations within control range
    Control the Injection Volume for A/F ratio Sensor
    Change injection volume
    -12.5% / 0% / 12.5%
    1. Perform test at less than 3000 rpm
    2. Control the Injection Volume for A/F Sensor enables checking and graphing of air fuel ratio sensor and heated oxygen sensor voltage outputs
    3. Perform the test at the engine speed 3000 rpm or less and engine coolant temperature 80°C (176°F) or more.
    4. Enrichment for over temperature protection off.
    5. To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / AFS voltage B1S1 and O2S B1S2
    Activate the VSV for Secondary Air Control
    Activate the Secondary Air System
    ON/OFF
    1. Do not perform the test for 5 seconds or more.
    2. After the test, do not perform the test again for 30 seconds.
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    Test possible when following
    1. Ignition switch to ON.
    2. Engine is stopped.
    Control the Fuel Pump/Speed
    Activate fuel pump
    ON/OFF
    Test possible when following
    1. Ignition switch to ON.
    2. Engine is stopped.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 are connected
    2. OFF: TC and TE1 are disconnected
    3. Ignition switch to ON.
    4. Engine is stopped.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    Idling fuel cut turned ON when throttle valve fully closed and engine speed over 2800 rpm
    1. Ignition switch to ON.
    2. Engine is stopped.
    Prohibit the Catalyst OT Misfire prevent F/C
    Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
    ON/OFF
    ON: Fuel cut is prohibited
    Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens slowly
    Test possible when following conditions met:
    1. Ignition switch to ON
    2. Engine does not start
    3. Fully depressing accelerator pedal (accelerator pedal position: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens quickly
    Test possible when following conditions met:
    1. Ignition switch to ON
    2. Engine does not start
    3. Fully depressing accelerator pedal (accelerator pedal position: 58 degrees or more)
    Control the VVT Linear (Bank 1)
    VVT actuator
    -128 to 127%
    OCV control duty ratio can be set to any value within this range
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated at 100% or more.
    2. This test is possible while idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 1)
    Turn on and off camshaft timing oil control valve assembly
    ON/OFF
    1. Engine stalls or idles roughly when camshaft oil control valve turned ON
    2. Normal engine running or idling when oil control valve is off
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Activate the Vacuum Pump
    Leak detection pump
    ON/OFF
    -
    Activate the VSV for Vent Value
    Vent valve
    ON/OFF
    -
    Control the Select Cylinder Fuel Cut
    Selected cylinder (cylinder #1 to #4) injector fuel cut
    #1/#2/#3/#4 ON/OFF
    Test possible during vehicle stopping and engine idling*1
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    Same as above
    Check the Cylinder Compression*2
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders

    NOTICE:
    *1
    1. If the display of the Data List Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
    2. If the display of the Data List Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
      1. Stop the engine, turn the ignition switch to ON.
      2. Enter the Control the Select Cylinder Fuel Cut.
      3. Select the cylinder for fuel cut (cylinder #1 to #4) and turn the Active Test ON (press the RIGHT or LEFT button).
      4. Start the engine.

    HINT:
    *2: In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).

    10. Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the Techstream.

      HINT:
      At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
      3. Use a fully-charged battery.

    11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    12. Push the snapshot button to turn the snapshot function off.
    13. Select "Stored Data" on the Techstream screen, select the recorded data and display the data as a graph.

      HINT:
      If the data is not displayed as a graph, the change of the values cannot be observed.

    14. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs (Pending DTCs) are stored, and can detect potential malfunctions in the system. System Check can be performed with the Techstream.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON and turn the Techstream on.

  3. Enter the following menus: Powertrain / Engine and ECT / Utility.

  4. Perform the System Check by referring to the table below.

  5. Turn the ignition switch OFF.

    Tester Display
    Test Part
    Control Range
    Diagnostic Notes
    Evaporative System Check
    (Automatic Mode)
    Perform 6 steps in order to operate EVAP key-off monitor automatically
    -
    1. Fuel temperature 35°C (95°F) or less
    2. If no DTCs in Pending DTCs after performing this test, system functioning normally
    3. Refer to EVAP Inspection Procedure (Click here)
    Evaporative System Check
    (Manual Mode)
    Perform 6 steps in order to operate EVAP key-off monitor manually
    -
    1. Fuel temperature 35°C (95°F) or less
    2. Used to detect malfunctioning parts
    3. Refer to EVAP Inspection Procedure (Click here)
    Secondary Air Injection Check
    (Automatic Mode)
    Perform secondary air injection system operation automatically
    -
    1. With warm engine, ignition switch turned off once
    2. If no DTCs in Pending DTCs after performing this test, system functioning normally
    3. Refer to inspection procedure for secondary air injection system DTCs
    4. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned ON or engine running
    5. Turn ignition switch off when System Check finished
    Secondary Air Injection Check
    (Manual Mode)
    Perform secondary air injection system operation manually Select monitor item 1, 2 or 3
    1. AIR PUMP: ON
      ASV: OPEN
    2. AIR PUMP: OFF
      ASV: CLOSE
    3. AIR PUMP: ON
      ASV: CLOSE
    -
    1. With warm engine, ignition switch turned OFF once
    2. Used to detect malfunctioning parts
    3. Refer to inspection procedure for secondary air injection system DTCs
    4. When performing Secondary Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned ON or engine running
    5. Turn ignition switch off when System Check finishes