SFI SYSTEM > EVAP System |
| DTC No. | Monitoring Item | See procedure |
| P043E | Reference orifice clogged (built into canister pump module) |
Click here
|
| P043F | Reference orifice high-flow (built into canister pump module) | |
| P0441 |
|
Click here
|
| P0451 |
|
Click here
|
| P0452 | Canister pressure sensor (built into canister pump module) voltage low | |
| P0453 | Canister pressure sensor (built into canister pump module) voltage high | |
| P0455 | EVAP gross leak |
Click here
|
| P0456 | EVAP small leak | |
| P2401 | Leak detection pump stuck OFF (built into canister pump module) |
Click here
|
| P2402 | Leak detection pump stuck ON (built into canister pump module) | |
| P2419 | Vent valve stuck closed (built into canister pump module) | |
| P2420 | Vent valve stuck open (vent) (built into canister pump module) |
Click here
|
| P2610 | Soak timer (built into ECM) |
Click here
|


| *1 | Purge VSV | *2 | EVAP Hose (to Intake Manifold) |
| *3 | EVAP Hose (from Canister) | *4 | Canister Pump Module - Canister Pressure Sensor - Leak Detection Pump - Vent Valve |
| *5 | Canister | *6 | Canister Filter |
| *7 | Air Inlet Port | *8 | Fuel Tank Cap Assembly |
| *9 | Fuel Tank | *10 | Purge Line |
| *11 | Bleeding Pipe | *12 | Refueling Valve |
| *a | Location of EVAP (Evaporative Emission) System | - | - |

| *1 | Intake Manifold | *2 | Purge VSV |
| *3 | Throttle Valve | *4 | Canister (Charcoal Filter) |
| *5 | Cut-off Valve | *6 | Fuel Tank |
| *7 | Air Cleaner | *8 | ECM |
| *9 | Canister Filter | *10 | Soak Timer |
| *11 | Canister Pump Module | *12 | Fuel Tank Cap Assembly |
| *13 | Roll-Over Valve | *14 | Refueling Valve |
| *15 | Restrictor (0.08 inch) | - | - |
| *a | EVAP System Circuit | - | - |
| Key-off monitor |
| Purge flow monitor |

| *1 | ECM | *2 | Soak Timer |
| *3 | Purge VSV (on) | *4 | Fuel Tank Cap Assembly |
| *5 | Canister Filter | *6 | Fuel Tank |
| *7 | Leak Detection Pump (0.02 inch) | *8 | Canister Pressure Sensor |
| *9 | Reference Orifice (0.02 inch) | *10 | Vent Valve (off) |
| *11 | Canister Pump Module | *12 | Canister |
| *13 | Refueling Valve | - | - |
| *a | EVAP Purge Flow | *b | to Intake Manifold |
| *c | to Atmosphere | - | - |
| Component | Operation |
| Canister | Contains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank. |
| Cut-off valve | Located in fuel tank. Valve floats and closes when fuel tank is 100% full. |
| Purge VSV (Vacuum Switching Valve) | Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake manifold controlled by purge VSV duty cycle (current-carrying time). (Open: on, Close: off) |
| Refueling valve | Controls EVAP pressure from fuel tank to canister. Valve consists of diaphragm, spring and restrictor (diameter: 0.08 inch). When fuel vapor and pressure inside fuel tank increase, valve opens. While EVAP purged, valve closes and restrictor prevents large amount of vacuum from affecting pressure in fuel tank. Valve opened while refueling. |
| Roll-over valve | Located in fuel tank. Valve closes by its own weight when vehicle overturns to prevent fuel from spilling out. |
| Soak timer | Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+/-15 min) after ignition switch is turned off. This allows fuel to cool down, stabilizing EVAP pressure. When approximately 5 hours elapsed, ECM activates (refer to fig. 3) |
| Canister pump module | Consists of (a) to (d) below. Canister pump module cannot be disassembled. |
| (a) Vent valve | Vents and closes EVAP system. When ECM turns valve on, EVAP system closed. When, ECM turns valve off, EVAP system is vented. Negative pressure (vacuum) is created in EVAP system to check for EVAP leaks by closing purge VSV, turning on vent valve (closing it) and operating leak detection pump (refer to fig. 1). |
| (b) Canister pressure sensor | Indicates pressure as voltages. ECM supplies regulated 5 V to canister pressure sensor, and uses feedback from sensor to monitor EVAP system pressure (refer to fig. 2). |
| (c) Leak detection pump | Creates negative pressure (vacuum) in EVAP system for leak check. |
| (d) Reference orifice | Has opening with 0.02 inch diameter. Vacuum is produced through orifice by closing purge VSV, turning off vent valve and operating leak detection pump, to monitor reference pressure. Reference pressure indicates a small leak of EVAP. |

| *1 | Canister | *2 | Reference Orifice (0.02 Inch) |
| *3 | Canister Pressure Sensor | - | - |
| *a | Canister Pump Module (fig. 1) | *b | Airflow |
| *c | Condition: Purge Flow | *d | Condition: Leak Check |
| *e | Vent Valve: off (vent) | *f | to Canister Filter (Atmosphere) |
| *g | Leak Detection Pump: off | *h | Vent Valve: on (closed) |
| *i | Leak Detection Pump: on | - | - |


| 1.CONFIRM DTC |
Turn the ignition switch off and wait for 10 seconds.
Turn the ignition switch to ON.
Turn the ignition switch off and wait for 10 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm DTCs and freeze frame data. If any EVAP system DTCs are stored, the malfunctioning area can be determined using the table below.

| NEXT | |
| 2.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.
| NEXT | |
| 3.PERFORM EVAPORATIVE SYSTEM CHECK (MANUAL MODE) |

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Manual Mode.
| NEXT | |
| 4.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6) |

Check the EVAP pressure in step 1/6.
| DTC*1 | Result | Suspected Trouble Area | Proceed to |
| - | Virtually no variation in EVAP pressure | Not yet determined | A |
| P0451 | EVAP pressure fluctuates by +/-0.3 kPa(gauge) [2.25 mmHg(gauge)] or more | Canister pressure sensor signal noise | B |
| P0452 or P0453 *2 |
| Canister pressure sensor or its circuit has malfunction | C |
|
| ||||
|
| ||||
| A | |
| 5.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6 TO 2/6) |

Check the EVAP pressure in steps 1/6 and 2/6.
| DTC* | Result | Suspected Trouble Area | Proceed to |
| - | Virtually no variation in EVAP pressure during step 1/6. Then decreases to reference pressure | Not yet determined | A |
| P2402 | Small difference between EVAP pressures during steps 1/6 and 2/6 | Leak detection pump stuck ON | B |
|
| ||||
| A | |
| 6.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6) |

Check the EVAP pressure 4 seconds after the leak detection pump is activated*1 (A).
*1: The leak detection pump begins to operate as step 1/6 finishes and step 2/6 starts.
Check the EVAP pressure again when it has stabilized. This pressure is the reference pressure (B).
| DTC*2 | Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure in inspection item (B) is between -4.85 kPa(gauge) and -1.157 kPa(gauge) [-36.381 mmHg(gauge) and -8.678 mmHg(gauge)] | Not yet determined | A |
| P043F and P2401 | EVAP pressure in inspection item (B) is -1.157 kPa(gauge) [-8.678 mmHg(gauge)] or more |
| B |
| P043E | EVAP pressure in inspection item (B) is less than -4.85 kPa(gauge) [-36.384 mmHg(gauge)] | Reference orifice clogged | C |
| P2419 | EVAP pressure in inspection item (A) is more than -1.157 kPa(gauge) [-8.678 mmHg(gauge)] |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 7.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6 TO 3/6) |

Ceck the EVAP pressure in step 3/6.
| DTC* | Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure increases by 0.3 kPa(gauge) [2.25 mmHg(gauge)] or more within 10 seconds of proceeding from step 2/6 to step 3/6 | Not yet determined | A |
| P2420 | No variation in EVAP pressure even after proceeding from step 2/6 to step 3/6 |
| B |
| P0451 | No variation in EVAP pressure during steps 1/6 through 3/6 |
| C |
|
| ||||
|
| ||||
| A | |
| 8.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6) |

Wait until the EVAP pressure change is less than 0.12 kPa(gauge) [0.9 mmHg(gauge)] for 40 seconds.
Measure the EVAP pressure and record it.
| NEXT | |
| 9.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 4/6) |

Check the EVAP pressure in step 4/6.
| DTC*1 | Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure increases by 0.4 kPa(gauge) [3 mmHg(gauge)] or more within 10 seconds of proceeding from step 3/6 to step 4/6 | Not yet determined | A |
| P0441 *2 | EVAP pressure increases by 0.4 kPa(gauge) [3 mmHg(gauge)] or more within 10 seconds of proceeding from step 3/6 to step 4/6 |
| B |
| P0441 | Variation in EVAP pressure is less than 0.4 kPa(gauge) [3 mmHg(gauge)] for 10 seconds, after proceeding from step 3/6 to step 4/6 |
| C |
|
| ||||
|
| ||||
| A | |
| 10.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 5/6) |

Check the EVAP pressure in step 5/6.
Compare the EVAP pressure in step 3/6 and the second reference pressure (step 5/6).
| DTC* | Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure from step 3/6 lower than second reference pressure (step 5/6) | Not yet determined (no leakage from EVAP system) | A |
| P0441 and P0455 | EVAP pressure from step 3/6 higher than [second reference pressure (step 5/6) x 0.2] |
| B |
| P0456 | EVAP pressure from step 3/6 higher than second reference pressure (step 5/6) | EVAP small leak | B |
|
| ||||
|
| ||||
| 11.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6) |

Check the EVAP pressure in step 3/6.
| DTC* | Result | Suspected Trouble Area | Proceed to |
| P043F | EVAP pressure less than [reference pressure] measured in step 2/6 | Reference orifice high-flow | A |
| P2401 | EVAP pressure almost same as [reference pressure] measured in step 2/6 | Leak detection pump stuck off | B |
|
| ||||
|
| ||||
| 12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR) |
Check the canister pressure sensor circuit, referring to DTC P0451 canister pressure sensor circuit inspection procedure (Click here).
|
| ||||
| 13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION) |
![]() |
Turn the ignition switch off.
Disconnect the canister connector.
Apply the battery voltage to terminals VLVB and VGND of the canister pump module.
Touch the canister pump module to confirm the vent valve operation.
| *a | Component without harness connected (Canister Pump Module) |
| Condition | Test Result | Suspected Trouble Area | Proceed to |
| Apply battery voltage to terminals VLVB and VGND | Operating |
| A |
| Not operating | Vent valve | B |
|
| ||||
| A | |
| 14.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E8-5 (VPMP) - L1-8 (VGND) | Always | Below 1 Ω |
| E8-5 (VPMP) or L1-8 (VGND) - Body ground | Always | 10 kΩ or higher |
| Result | Suspected Trouble Area | Proceed to |
| OK |
| A |
| NG | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
| A | |
| 15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND) |
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| L1-6 (MGND) - Body ground | Always | Below 1 Ω |
| A |
| 10 kΩ or higher | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
| A | |
| 16.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| E8-6 (MPMP) - L1-1 (MTRB) | Always | Below 1 Ω |
| A |
| 10 kΩ or higher | Wire harness or connector between canister pump module and body ground | B |
|
| ||||
|
| ||||
| 17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV) |
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.
Disconnect the hose (connected to the canister) from the purge VSV.
Start the engine.
Using the Techstream, turn off the purge VSV (Activate the VSV for Evap Control: OFF).
Use your finger to confirm that the purge VSV has no suction.
Using the Techstream, turn on the purge VSV (Activate the VSV for Evap Control: ON).
Use your finger to confirm that the purge VSV has suction.
| *1 | Hose (to canister) |
| *2 | Purge VSV |
| Result | Suspected Trouble Area | Proceed to |
| No suction when purge VSV turned off, and suction applied when turned on | Blockage in the purge line is considered (based on result of step 9):
| A |
Leakage is considered (based on result of step 10):
| B | |
| Suction applied when purge VSV turned off | Purge VSV stuck open | C |
| No suction when purge VSV turned on |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 18.INSPECT EVAP HOSE (PURGE VSV - CANISTER) |
Check for blockages in the EVAP purge line between the purge VSV and canister.
|
| ||||
| OK | |
| 19.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER) |
Check for filter blockage in the canister (Click here).
|
| ||||
|
| ||||
| 20.CHECK FUEL TANK CAP ASSEMBLY |
Check that the fuel tank cap assembly is correctly installed and confirm that the fuel tank cap assembly meets OEM specifications.
Tighten the fuel tank cap assembly firmly (only one click sound could be heard).
Remove the fuel tank cap assembly and install it onto a fuel tank cap assembly adapter.
Connect an EVAP tester pump hose to the adapter, and pressurize the cap to 3.2 to 3.7 kPa(gauge) [24 to 28 mmHg(gauge)] using an EVAP tester pump.
Seal the adapter and wait for 2 minutes.
Check the pressure. If the pressure is 2 kPa(gauge) [15 mmHg(gauge)] or more, the fuel tank cap assembly is normal.
| Result | Suspected Trouble Area | Proceed to |
| Fuel tank cap assembly correctly installed | - | A |
| Fuel tank cap assembly loose |
| B |
| Defective fuel tank cap assembly | - | B |
| No fuel tank cap assembly | - | C |
|
| ||||
|
| ||||
|
| ||||
| 21.INSPECT PURGE VSV |
![]() |
Turn the ignition switch off.
Disconnect the purge VSV connector.
Disconnect the hose (connected to the canister) from the purge VSV.
Start the engine.
Use your finger to confirm that the purge VSV has no suction.
| *1 | Hose (to canister) |
| *2 | Purge VSV |
| *3 | Connector |
| Result | Suspected Trouble Area | Proceed to |
| No suction |
| A |
| Suction applied | Purge VSV | B |
|
| ||||
|
| ||||
| 22.INSPECT EVAP HOSE (PURGE VSV - CANISTER) |
Check for blockages in the EVAP purge line between the purge VSV and canister.
|
| ||||
| OK | |
| 23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD) |
![]() |
Disconnect the hose (connected to the intake manifold) from the purge VSV
Start the engine.
Use your finger to confirm that the hose has suction.
| *1 | Purge VSV |
| *2 | Hose (to intake manifold) |
| Result | Suspected Trouble Area | Proceed to |
| Suction applied | EVAP hose between purge VSV and intake manifold normal
| A |
| No suction |
| B |
|
| ||||
| A | |
| 24.INSPECT PURGE VSV |
![]() |
Remove the purge VSV.
Apply the battery voltage to the terminals of the purge VSV.
Confirm that air flows from port E to port F.
| *1 | Purge VSV |
| *a | Port E |
| *b | Port F |
| *c | Air |
| Test Result | Condition | Suspected Trouble Area | Proceed to |
| Air flows | Battery voltage is applied to purge VSV terminals | Purge VSV normal
| A |
| No air flow | Battery voltage is applied to purge VSV terminals | Purge VSV | B |
|
| ||||
| A | |
| 25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV) |
![]() |
Disconnect the purge VSV connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector (to Purge VSV) |
| Tester Connection | Switch Condition | Test Result | Suspected Trouble Area | Proceed to |
| V4-1 - Body ground | Ignition switch ON | 11 to 14 V | Purge VSV power source normal
| A |
| Other than result above | Wire harness or connectors between purge VSV and battery | B |
|
| ||||
| A | |
| 26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Disconnect the ECM connector.
Disconnect the purge VSV connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E5-23 (PRG) - V4-1 (Purge VSV) | Always | Below 1 Ω |
| E5-23 (PRG) - Body ground | Always | 10 kΩ or higher |
| V4-2 (Purge VSV) - Body ground | Always | 10 kΩ or higher |
|
| ||||
|
| ||||
| 27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VENT VALVE) |
![]() |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector (to Canister Pump Module) |
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| L1-9 (VLVB) - Body ground | Ignition switch ON | 11 to 14 V |
| A |
| Below 3 V |
| B |
|
| ||||
| A | |
| 28.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION) |
![]() |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Apply the battery voltage to terminals VLVB and VGND of the pump module.
Touch the canister pump module to confirm the vent valve operation
| *a | Component without harness connected (Canister Pump Module) |
| Condition | Test Result | Suspected Trouble Area | Proceed to |
| Apply battery voltage to terminals VLVB and VGND | Operating |
| A |
| Not operating |
| B |
|
| ||||
| A | |
| 29.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| E8-5 (VPMP) - L1-8 (VGND) | Always | Below 1 Ω |
| A |
| 10 kΩ or higher | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
| A | |
| 30.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER) |
Check for filter blockage in the canister (Click here).
|
| ||||
|
| ||||
| 31.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE VACUUM PUMP) |
![]() |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Vacuum Pump.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector (to Canister Pump Module) |
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| L1-1 (MTRB) - Body ground | Leak detection pump on and off (Active Test ON and OFF) | Below 3 V when OFF 9 to 14 V when ON |
| A |
| Below 3 V when OFF and ON |
| B | ||
| 9 to 14 V when OFF and ON |
| C |
|
| ||||
|
| ||||
| A | |
| 32.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND) |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| L1-6 (MGND) - Body ground | Always | Below 1 Ω | Leak detection pump | A |
| 10 kΩ or higher | Wire harness or connector between canister pump module and body ground | B |
|
| ||||
|
| ||||
| 33.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE) |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E8-6 (MPMP) - L1-1 (MTRB) | Always | Below 1 Ω |
| E8-6 (MPMP) or L1-1 (MTRB) - Body ground | Always | 10 kΩ or higher |
| Result | Suspected Trouble Area | Proceed to |
| OK | ECM | A |
| NG | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
|
| ||||
| 34.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT) |
Stop the engine.
Disconnect the EVAP hose from the intake manifold.
Start the engine.
Use your finger to confirm that the port of the intake manifold has suction.
| Result | Suspected Trouble Area | Proceed to |
| Suction applied | EVAP hose between intake manifold and purge VSV | A |
| No suction | Intake manifold | B |
|
| ||||
|
| ||||
| 35.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY |
|
| ||||
| 36.REPLACE FUEL TANK CAP ASSEMBLY |
|
| ||||
| 37.LOCATE EVAP LEAK PART |
Disconnect the vent hose.

| *1 | Fuel Tank | *2 | Canister |
| *3 | Vent Hose | *4 | Air Filter |
| *5 | Fuel Tank Cap Assembly | - | - |
| *a | Disconnect the Vent Hose here | - | - |
Connect the EVAP pressure tester tool to the vent hose with the adapter.

| *1 | Canister | *2 | Adapter |
| *3 | EVAP Pressure Tester Tool | *4 | Adapter Hose |
Pressurize the EVAP system to 3.2 to 3.7 kPa(gauge) [24 to 28 mmHg(gauge)].
Apply soapy water to the piping and connecting parts of the EVAP system.
Look for areas where bubbles appear. This indicates the leak point.
Repair or replace the leak point.
|
| ||||
| 38.REPLACE CANISTER PUMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel Tank | *2 | Canister |
| *3 | Air Filter | *4 | Vent Hose |
| *5 | Air Inlet Hose | *6 | Fuel Tank Cap Assembly |
| *7 | Canister Pump Module | - | - |
| *a | Inspection Area (check for disconnection and/or crack) | - | - |
|
| ||||
| 39.REPLACE PURGE VSV |
Replace the purge VSV.
|
| ||||
| 40.REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| ||||
| 41.REPLACE EVAP PURGE LINE (INTAKE MANIFOLD - PURGE VSV) |
|
| ||||
| 42.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT) |
Check that the EVAP purge port of the intake manifold is not clogged. If necessary, replace the intake manifold (Click here).
|
| ||||
| 43.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS |
Repair the malfunctioning areas indicated by the DTCs that had been confirmed when the vehicle was brought in.
|
| ||||
| 44.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VSV - CANISTER) |
|
| ||||
| 45.REPLACE CANISTER ASSEMBLY |
Replace the canister assembly (Click here).

| *1 | Fuel Tank | *2 | Canister |
| *3 | Air Filter | *4 | Vent Hose |
| *5 | Air Inlet Hose | *6 | Fuel Tank Cap Assembly |
| *7 | Canister Pump Module | - | - |
| *a | Inspection Area (check for disconnection and/or crack) | - | - |
|
| ||||
| 46.REPLACE CANISTER PUMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel Tank | *2 | Canister |
| *3 | Air Filter | *4 | Vent Hose |
| *5 | Air Inlet Hose | *6 | Fuel Tank Cap Assembly |
| *7 | Canister Pump Module | - | - |
| *a | Inspection Area (check for disconnection and/or crack) | - | - |
| NEXT | |
| 47.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Result | Proceed to |
| EVAP system DTCs are output | A |
| No DTCs output (No pending DTCs output) | B |
|
| ||||
| A | |
| 48.REPLACE ECM |
Replace the ECM (Click here.
| NEXT | |
| 49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.
| NEXT | ||
| ||
| KEY-OFF MONITOR CONFIRMATION |
Preconditions
The monitor will not run unless:
Monitor Conditions
Monitor Status
| PURGE FLOW MONITOR CONFIRMATION (P0441) |
Preconditions
The monitor will not run unless:
Monitor Conditions
Monitor Status