Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal conditions are as shown in the table below.


Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
  1. [OFF] denotes ground potential.
  2. [ON] denotes battery potential (+B).
  3. On the Techstream, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
  1. (a) Ignition switch ON
  2. (b) Brake pedal released
  3. (c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM


A236803E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Stop light switch conditions can be checked using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.
    5. Check the Data List indication when the brake pedal is depressed and released.

      Brake Pedal Operation
      Stop Light Switch
      ST1
      Depressed
      ON
      ON
      Released
      OFF
      OFF

1.CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

OK:
Stop lights turn ON when brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.INSPECT STOP LIGHT SWITCH
A072924E02
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    3 - 4
    Switch pin free
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH
OK


3.READ DATA LIST (STP SIGNAL AND ST1 - VOLTAGE)
A093220E11
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Check the STP signal when the brake pedal is depressed and released.

    OK:
    Brake Pedal Operation
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-16 (ST1-) - E4-3 (E1)
    Brake pedal depressed
    Below 1.5 V
    E8-16 (ST1-) - E4-3 (E1)
    Brake pedal released
    7.5 to 14 V



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
A113676E04
  1. Disconnect the stop light switch connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    S10-1 (Stop light switch) - E7-4 (STP)
    Always
    Below 1 Ω
    S10-3 (Stop light switch) - E8-16 (ST1-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)