Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0125    Insufficient Coolant Temperature for Closed Loop Fuel Control

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Condition
Trouble Area
P0125
The engine coolant temperature does not reach the closed loop enabling temperature for 20 minutes (this period varies with the engine coolant temperature at engine start) (2 trip detection logic).
  1. Engine coolant temperature sensor
  2. Cooling system
  3. Thermostat

MONITOR DESCRIPTION

The resistance of the engine coolant temperature sensor varies in proportion to the actual engine coolant temperature. The ECM supplies a constant voltage to the sensor and monitors the signal output voltage of the sensor. The signal voltage output varies according to the changing resistance of the sensor. After the engine is started, the engine coolant temperature is monitored through this signal. If the engine coolant temperature sensor indicates that the engine is not yet warm enough for closed-loop fuel control, despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.
Example:
The engine coolant temperature is 5°C (41°F) at engine start. After 69 seconds running time, the engine coolant temperature sensor still indicates that the engine is not warm enough to begin closed-loop fuel (air fuel ratio feedback) control. The ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0125: Insufficient Engine Coolant Temperature for Closed-Loop Fuel Control
Required Sensors/Components (Main)
Thermostat
Cooling system
Required Sensors/Components (Related)
Engine coolant temperature sensor and mass air flow meter
Frequency of Operation
Continuous
Duration
69 seconds: Engine coolant temperature at engine start 8.33°C (46.99°F) or higher
114 seconds: Engine coolant temperature at engine start between 19.44°C (66.99°F) and 8.33°C (46.99°F)
1200 seconds: Engine coolant temperature at engine start less than 19.44°C (66.99°F)
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
None
Thermostat fail (P0128)
Not detected
Intake air temperature sensor circuit fail (P0112, P0113)
Not detected
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118)
Not detected
Mass air flow meter sensor circuit fail (P0102, P0103)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Time until actual engine coolant temperature reaches closed loop fuel control enabling temperature
69 seconds: Engine coolant temperature at engine start 8.33°C (46.99°F) or higher
114 seconds: Engine coolant temperature at engine start between 19.44°C (66.99°F) and 8.33°C (46.99°F)
1200 seconds: Engine coolant temperature at engine start less than 19.44°C (66.99°F)

CONFIRMATION DRIVING PATTERN

  1. Leave the vehicle outside overnight.
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON and turn the Techstream on.
  4. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
  5. Check that the engine coolant temperature is 10°C (50°F) or less.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Start the engine.
  10. Wait 21 minutes or more.
  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  12. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P0125.
  15. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  16. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0115 .

INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0116, P0117 or P0118 are stored simultaneously with DTC P0125, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0125)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0125
    A
    P0125 and other DTCs
    B

    HINT:
    If any DTCs other than P0125 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat (Click here).

    Standard value:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.



NG
REPLACE THERMOSTAT (Click here)
OK


3.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR