Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1-trip detection logic)
  1. (a) Vehicle speed 20 km/h (12.43 mph) or more
  2. (b) Engine speed 1000 rpm or more
  3. (c) STA signal ON
  1. Park/neutral position switch assembly*1
  2. Clutch start switch assembly*2
  3. Starter relay circuit
  4. Ignition switch
  5. ECM
  1. *1: for Automatic Transmission
    *2: for Manual Transmission

MONITOR STRATEGY


Related DTCs
P0617: Starter signal
Required Sensors/Components (Main)
STA relay
Park/neutral position switch
Clutch start switch
Ignition switch
Required Sensors/Components (Related)
Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or more
Vehicle speed
20 km/h (12.43 mph) or more
Engine speed
1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Starter signal
ON

CONFIRMATION DRIVING PATTERN


A231469E04

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Idle the engine for 5 seconds or more [B].
  7. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0617.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].

  13. Check the DTC judgment result [E].
  14. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A254617E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the Techstream when the ignition switch is turned to ON and START.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.INSPECT PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH
A193245E03
  1. Inspect the park/neutral position switch assembly (for automatic transmission).

    1. Disconnect the park/neutral position switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 - 6, 4 - 5
      Gear selector lever position P
      Below 1 Ω
      1 - 2
      Gear selector lever position R
      Below 1 Ω
      2 - 9, 4 - 5
      Gear selector lever position N
      Below 1 Ω
      2 - 7
      Gear selector lever position D
      Below 1 Ω
      2 - 3
      Gear selector lever position 2
      Below 1 Ω
      2 - 8
      Gear selector lever position L
      Below 1 Ω
      4 - 5
      Gear selector lever position except P and N
      10 kΩ or higher
      2 - 5
      Gear selector lever positions
      (P, R, N, D, 2 and L)
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Park/Neutral Position Switch Assembly)



    A193244E02
  1. Inspect the clutch start switch assembly (for manual transmission).

    1. Disconnect the clutch start switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Position
      Specified Condition
      1 - 2
      ON (pushed)
      Below 1 Ω
      1 - 2
      OFF (free)
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Clutch Start Switch Assembly)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH (GO TO STEP 3 AFTER REPLACEMENT)
OK


3.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the Techstream when the ignition switch is turned to ON and START.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 4
OK

END 

4.INSPECT IGNITION SWITCH
A193243E02
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    All Terminals
    LOCK
    10 kΩ or higher
    2 - 4
    ACC
    Below 1 Ω
    1 - 2, 1 - 4, 5 - 6
    ON
    Below 1 Ω
    1 - 3 - 4, 5 - 6 - 7
    START
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Ignition Switch)



NG
REPLACE IGNITION SWITCH (Click here)
OK


5.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the Techstream when the ignition switch is turned to ON and START.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - CLUTCH START SWITCH OR PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
OK

END