Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A237102E02


INSPECTION PROCEDURE

NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.INSPECT ECM (+B VOLTAGE)
A018294E37
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E8-1 (+B) - E4-3 (E1)
    Ignition switch ON
    9 to 14 V



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A065743E26
  1. Disconnect the cable from the negative battery terminal.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E4-3 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (IGSW VOLTAGE)
A018294E38
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E8-9 (IGSW) - E4-3 (E1)
    Ignition switch ON
    9 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 6
A


4.CHECK FUSE (AM2 AND IGN)
A115876E01
  1. Check the AM2 fuse.

    1. Remove the AM2 fuse from the engine room R/B.

    2. Check the AM2 fuse resistance.

      Standard resistance:
      Below 1 Ω

  1. Check the IGN fuse.

    1. Remove the IGN fuse from the driver side J/B.

    2. Check the IGN fuse resistance.

      Standard resistance:
      Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


5.INSPECT IGNITION SWITCH ASSEMBLY
G037118E04
  1. Disconnect the I7 ignition switch assembly connector.

  1. Check the resistance.

    Standard Resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All Terminals
    LOCK
    10 kΩ or higher
    2-4
    ACC
    Below 1 Ω
    1-4, 2-4, 5-6
    ON
    Below 1 Ω
    1-4, 3-4, 5-6, 5-7
    START
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

CHECK AND REPAIR HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY - ECM) 

6.INSPECT ECM (MREL VOLTAGE)
A018294E39
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E8-8 (MREL) - E4-3 (E1)
    Ignition switch ON
    9 to 14 V



NG
REPLACE ECM (Click here)
OK


7.CHECK FUSE (EFI)
G035646E02
  1. Remove the EFI fuse from the engine room R/B.

  1. Check the EFI fuse resistance.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


8.INSPECT EFI RELAY
A054773E02
  1. Remove the EFI relay from the engine room R/B.

  1. Check the EFI relay resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    3 - 5
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE EFI RELAY
OK


9.CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM, EFI RELAY - BODY GROUND)
A115877E02
  1. Check the harness and connector between the EFI relay and ECM.

    1. Remove the EFI relay from the engine room R/B.

    2. Disconnect the E8 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      EFI relay terminal 1 (Engine room R/B) - E8-8 (MREL)
      Always
      Below 1 Ω
      EFI relay terminal 3 (Engine room R/B) - E8-1 (+B)
      Always
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connection
      Condition
      Specified Condition
      EFI relay terminal 1 (Engine room R/B) or E8-8 (MREL) - Body ground
      Always
      10 kΩ or higher
      EFI relay terminal 3 (Engine room R/B) or E8-1 (+B) - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and connector between the EFI relay and body ground.

    1. Remove the EFI relay from the engine room R/B.

    2. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      EFI relay terminal 2 (Engine room R/B) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPLACE HARNESS OR CONNECTOR (TERMINAL 5 OF EFI RELAY - BATTERY POSITIVE TERMINAL)