Home › ENGINE ยท 1GR-FE › COOLING › WATER PUMP

WATER PUMP > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type)
  1. Remove the 4 bolts, then remove the engine under cover.



3. DRAIN ENGINE COOLANT


A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



4. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH


G036137E02
  1. Disengage the 9 clips, then remove the radiator support to frame seal.



5. REMOVE V-BANK COVER


A075593E01
  1. Remove the 2 nuts, then remove the V-bank cover.



6. REMOVE FAN SHROUD


G036138E01
  1. Disconnect the hose from the radiator reserve tank.



    G036139E01
  1. Remove the 2 cooler hoses from the clamp (with automatic transmission).

  1. Remove the 4 nuts from the fan pulley.

  1. Remove the fan and generator V belt .

  1. Remove the 2 bolts from the fan shroud.

  1. Remove the fan pulley and fan shroud.



7. REMOVE AIR CLEANER ASSEMBLY


A075594E01
  1. Disconnect the ventilation hose No. 2.



    A075595E01
  1. Disconnect the vacuum hose.

  1. Disconnect the mass air flow meter connector.

  1. Remove the 2 wire harness clamps.



    A075596E01
  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts, then remove the air cleaner.



8. REMOVE WATER INLET


A076334E01
  1. Disconnect the 2 oil cooler hoses (with oil cooler).



    A076335E02
  1. Disconnect the 2 radiator hoses.



    A076336E02
  1. Disconnect the 5 water by-pass hoses.



    A076337E03
  1. Remove the 5 bolts and water inlet.

  1. Remove the O-ring from the water outlet pipe.

  1. Remove the gasket from the water pump.



9. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


A076338E02
  1. Remove the 2 bolts, then remove the 2 idler pulleys.



10. REMOVE GENERATOR ASSEMBLY


A076407E01
  1. Disconnect the wire harness.

    1. Remove the bolt and wire harness stay.

    2. Disconnect the connector from the generator assembly.

    3. Remove the terminal cap and nut.

    4. Disconnect the wire harness from terminal B.



    A076408E01
  1. Remove the 2 bolts, then separate the wire harness clamp bracket from the generator assembly.



    A076409E01
  1. Remove the 2 bolts, then remove the generator assembly.



11. SEPARATE COOLER COMPRESSOR ASSEMBLY


G036154E01
  1. Remove the bolt, then separate the suction hose sub-assembly.



    G036155E01
  1. Disconnect the cooler compressor assembly connector.

  1. Remove the 4 bolts, then separate the cooler compressor assembly from the V-ribbed belt tensioner assembly.



12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

HINT:
Drive Type
See Page
2WD
Click here
Pre Runner and 4WD
Click here



13. REMOVE WATER PUMP ASSEMBLY


A072954E03
  1. Remove the 17 bolts, then remove the water pump and gasket.