AUTOMATIC TRANSMISSION SYSTEM > DIAGNOSIS SYSTEM |
| DESCRIPTION |
When troubleshooting on-Board Diagnostic (OBD II) vehicles, the vehicle must be connected to the Techstream (complying with SAE J1987). Various data output from the vehicle's ECM can then be read.
![]() |
OBD II regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
To check DTCs, connect the Techstream to the Data Link Connector 3 (DLC3) of the vehicle. Techstream displays DTCs, the freeze frame data and a variety of the engine data.
The DTCs and freeze frame data can be cleared with the Techstream (Click here).
In order to enhance OBD function on vehicles and develop the Off-Board diagnosis system, CAN communication has been introduced in this system (CAN: Controller Area Network). It minimizes the gap between technician skills and vehicle technology. CAN is a network, which uses a pair of data transmission lines, spanning multiple computers and sensors. It allows high speed communication between the systems and simplification of the wire harness connection. Since this system is equipped with CAN communication, connecting with the Techstream is necessary to display any information from the ECM. (Also communication between the Techstream and the ECM uses a CAN communication signal.) When confirming DTCs and any data of the ECM, connect the Techstream to the DLC3.
| NORMAL MODE AND CHECK MODE |
The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2-trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1-trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions.
| 2 TRIP DETECTION LOGIC |
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the ignition switch is turned off and then ON again, and the same malfunction is detected again, the MIL will illuminate.
| FREEZE FRAME DATA |
Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
![]() |
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
| DATA LINK CONNECTOR 3 (DLC3) |
![]() |
The vehicle's ECM uses the ISO 15765-4 communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.
| *a | Front view of DLC3 |
| Symbol (Terminal No.) | Terminal Description | Condition | Specified Condition |
| SIL (7) - SG (5) | Bus "+" line | During transmission | Pulse generation |
| CG (4) - Body ground | Chassis ground | Always | Below 1 Ω |
| SG (5) - Body ground | Signal ground | Always | Below 1 Ω |
| BAT (16) - Body ground | Battery positive | Always | 11 to 14 V |
| CANH (6) - CANL (14) | CAN bus line | Ignition switch off* | 54 to 69 Ω |
| CANH (6) - Battery positive | HIGH-level CAN bus line | Ignition switch off* | 6 kΩ or higher |
| CANH (6) - CG (4) | HIGH-level CAN bus line | Ignition switch off* | 200 Ω or higher |
| CANL (14) - Battery positive | LOW-level CAN bus line | Ignition switch off* | 6 kΩ or higher |
| CANL (14) - CG (4) | LOW-level CAN bus line | Ignition switch off* | 200 Ω or higher |
| CHECK BATTERY VOLTAGE |
If the voltage is below 11 V, replace the battery before proceeding.
| CHECK MIL |
Check that the MIL illuminates when turning the ignition switch to ON.
If the MIL does not illuminate, there is a problem in the MIL circuit (Click here).
When the engine is started, the MIL should turn off.