Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Turbine Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The sensor detects the rotation speed of the turbine which shows the input revolution of the transmission.
By comparing the input turbine speed signal (NCO) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No.
DTC Detection Condition
Trouble Area
P0717
ECM detects conditions (a), (b) and (c) continuously for 5 seconds or more. (1-trip detection logic)
(a) Output shaft speed is 500 rpm or more. (Vehicle speed: 50 km/h (31 mph) or more)
(b) Park/neutral position switch:
NSW input signal is OFF
R input signal is OFF
(c) Speed sensor (NCO):
Less than 300 rpm
  1. Open or short in speed sensor (NCO) circuit
  2. Speed sensor (NCO)
  3. ECM

Reference (Using an oscilloscope):
Check the waveform between terminals NCO+ and NCO- of the ECM connector.
G020663E04

Standard:
Refer to the illustration.
Item
Content
Terminal
NCO+ - NCO-
Tool setting
1 V/DIV
2 ms/DIV
Vehicle condition
Engine is idling (P or N position)


MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NCO (Turbine (input) speed sensor) or is weak. The NCO terminal of the ECM detects the pulse signal from speed sensor (NCO) (input RPM). The ECM outputs a gear shift signal comparing the speed sensor (NCO) with the output speed sensor (SP2).
If the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 500 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: A pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0717: Speed sensor (NCO)/Verify pulse input
Required sensors/Components
Speed sensor (NCO)
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0751, P0973, P0974 (Shift solenoid valve S1)
P0756, P0976, P0977 (Shift solenoid valve S2)
Output shaft rpm
500 rpm or more
Park/neutral position switch
OFF
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
R switch
OFF
Transmission range switch fail (P0705)
Not detected
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Sensor signal rpm
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor (NCO)
Input speed is equal to engine speed when lock-up is ON.

WIRING DIAGRAM


C121791E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
According to the Data List displayed by Techstream, you can read the values of switches, sensors, actuators and so on without removing parts. Reading the Data List as the first step of troubleshooting is one method to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NC0)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up is:
    1. ON (after warming up engine): Input turbine speed (NC0) is equal to engine speed
    2. OFF (idling with shift lever on N): Input turbine speed (NC0) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm

    HINT:
    1. SPD (NCO) is always 0 while driving indicates:
      3rd Gear: Open or short in the sensor or circuit.
      4th Gear: Engine speed 0 rpm
    2. SPD (NCO) is always less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more indicates:
      Sensor trouble, improper installation, or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR INSTALLATION


    BR03795E01
  1. Check the speed sensor (NCO) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
REPLACE SPEED SENSOR (NCO) (Click here)
OK


2.INSPECT SPEED SENSOR (NCO)


    C110343E18
  1. Disconnect the speed sensor connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    560 to 680 Ω at 20°C (68°F)



NG
REPLACE SPEED SENSOR (NCO) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM)


    C095812E37
  1. Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    E5-34 (NCO+) - E5-26 (NCO-)
    560 to 680 Ω at 20°C (68°F)
    E5-34 (NCO+) - Body ground
    10 kΩ or higher
    E5-26 (NCO-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)