Home › TRANSMISSION · A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Turbine Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The sensor detects the rotation speed of the turbine which shows the input revolution of the transmission.
By comparing the input turbine speed signal (NCO) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No.
DTC Detection Condition
Trouble Area
P0717
ECM detects conditions (a), (b) and (c) continuously for 5 seconds or more. (1 trip detection logic)
(a) Output shaft speed is 500 rpm or more. (Vehicle speed: 50 km/h (31 mph) or more)
(b) Park/neutral position switch:
NSW input signal is OFF
R input signal is OFF
(c) Speed sensor (NCO):
Less than 300 rpm
  1. Wire harness or connector
  2. Speed sensor (NCO)
  3. ECM
Using an oscilloscope:
Check the waveform between terminals NCO+ and NCO- of the ECM connector.
G020663E04

Standard:
Refer to the illustration.

Terminal
NCO+ - NCO-
Tool setting
1 V/DIV, 2 ms/DIV
Vehicle condition
Engine is idling (P or N position)

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NCO (Turbine (input) speed sensor) or is weak. The NCO terminal of the ECM detects the pulse signal from speed sensor (NCO) (input speed). The ECM outputs a gear shift signal comparing the speed sensor (NCO) with the output speed sensor (SP2).
If the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 500 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: A pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0717: Speed sensor (NCO)/Verify pulse input
Required sensors/Components
Speed sensor (NCO)
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present.
P0751, P0973, P0974 (Shift solenoid valve S1)
P0756, P0976, P0977 (Shift solenoid valve S2)
Output shaft speed
500 rpm or more
Park/neutral position switch
OFF
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
R switch
OFF
Transmission range switch fail (P0705)
Not detected
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Sensor signal speed
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor (NCO)
Input speed is equal to engine speed when lock-up is ON.

WIRING DIAGRAM


C186140E06


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NC0)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
  1. Input turbine speed (NCO) equal to engine speed: Lock-up ON (after warming up engine)
  2. Input turbine speed (NCO) nearly equal to engine speed: Lock-up OFF (idling with shift lever in N)
Data is displayed in increments of 50 rpm.

HINT:
  1. SPD (NC0) is always 0 while driving:
    Open or short in the sensor or circuit.
  2. SPD (NC0) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:
    Sensor trouble, improper installation, or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR (NCO) INSTALLATION


    C211922E01
  1. Check the speed sensor (NCO) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    Correct
    *b
    Incorrect



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (NCO) (Click here)
OK


2.INSPECT SPEED SENSOR (NCO)


    C224016E01
  1. Disconnect the speed sensor (NCO) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Speed Sensor (NCO))



NG
REPLACE SPEED SENSOR (NCO) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NCO) - ECM)


    C223988E01
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E5-34 (NCO+) - E5-26 (NCO-)
    20°C (68°F)
    560 to 680 Ω
    E5-34 (NCO+) - Body ground
    Always
    10 kΩ or higher
    E5-26 (NCO-) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Rear view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)