Home › TRANSMISSION ยท A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2741    Transmission Fluid Temperature Sensor "B" Performance

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the ECM. The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1, and the ECM calculates the fluid temperature based on the voltage signal.

HINT:
The ATF temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No.
DTC Detection Condition
Trouble Area
P2741
When one of the condition below is met:
  1. ATF level
  2. Transmission wire (No. 1 ATF temperature sensor)
Condition (A):
(a), (b), (c) or (d) are detected: (2-trip detection logic)
(a) After the engine is stopped, 5 hours or more elapse before the engine is started.
(b) After normal driving for 10 minutes and 5.0 km (3.1 miles) or more.
(c) Engine coolant and intake air temperature is 15°C (59°F) or more at 12 seconds after engine start.
(d) ATF temperature is less than 20°C (68°F).
Condition (B):
All of (a), (b) and (c) are detected (2-trip detection logic)
(a) After normal driving for 21 minutes and 40 seconds and 9 km (5.6 miles) or more.
(b) Engine coolant and intake air temperature is -10°C (14°F) or more at 12 seconds after engine start.
(c) ATF temperature is less than 20°C (68°F).
Condition (C):
Both (a) and (b) are detected (2-trip detection logic)
  1. (a) Engine coolant temperature is less than 35°C (95°F) at engine start.
  2. (b) ATF temperature is 110°C (230°F) or more when engine coolant temperature reaches 60°C (140°F).

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and turns on the MIL.
When the ATF temperature is 110°C (230°F) or more and the engine coolant temperature reaches 60°C (140°F) after a cold start, the ECM also interprets this as a fault, turns on the MIL, and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2741: ATF temperature sensor/Rationality check
Required sensors/Components
No. 1 ATF temperature sensor
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL 
The monitor will run whenever the following DTCs are not present
P2742, P2743 (Transmission temperature sensor "B" circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)

Condition (A) 
Time after engine start
10 minutes or more
Driving distance after engine start
5.0 km (3.1 miles) or more
IAT (12 seconds after engine start)
15°C (59°F) or more
ECT (12 seconds after engine start)
15°C (59°F) or more
Soak time
5 hours or more

Condition (B) 
Time after engine start
21 minutes and 40 seconds or more
Driving distance after engine start
9 km (5.6 miles) or more
IAT (12 seconds after engine start)
-10°C (14°F) or more
ECT (12 seconds after engine start)
-10°C (14°F) or more

Condition (C) 
Time after ECT reaches 60°C (140°F)
10 seconds or more
ATF temperature (12 seconds after engine start)
110°C (230°F) or more
ECT (12 seconds after engine start)
Less than 35°C (95°F)

TYPICAL MALFUNCTION THRESHOLDS


Condition (A) and (B) 
ATF temperature
Less than 20°C (68°F)

Condition (C) 
ATF temperature
110°C (230°F) or more

COMPONENT OPERATING RANGE


ATF temperature
20 to 110°C (68 to 230°F)

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. Approximately 80°C (176°F): After stall test
    2. Equal to ambient temperature when engine cold
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P2742 is output and the Techstream output is 150°C (302°F) or higher, there is a short circuit.
    When DTC P2743 is output and the Techstream output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the Techstream in order to check if a malfunction exists.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit
    It is not necessary to inspect the circuit when P2741 is stored.
1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2741)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P2741 is output
    A
    P2741 and other DTCs are output
    B

    HINT:
    If any other codes besides P2741 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

    OK:
    Automatic transmission fluid level is correct.



NG
ADD FLUID (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR) (Click here)