Home › TRANSMISSION · A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION


C243319E01

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC No.
DTC Detection Condition
Trouble Area
P2714
ECM detects a malfunction with the solenoid valve SLT (ON side) according to difference in revolutions of turbine (input) and output shaft (2 trip detection logic)
  1. Shift solenoid valve SLT remains open or closed
  2. Valve body is blocked
  3. Torque converter assembly
  4. Automatic transmission (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

With the shift lever in any forward position, when the difference between the revolutions of the turbine and output shaft exceeds the specified value (varies with output speed) determined by the ECM, the ECM illuminates the MIL and outputs the DTC. When shift solenoid valve SLT remains on, the oil pressure goes down and the clutch engagement force decreases.

MONITOR STRATEGY


Related DTCs
P2714: Shift solenoid valve SLT/ON malfunction
Required sensors/Components
Shift solenoid valve SLT, Speed sensor (NT), Speed sensor (SPD)
Frequency of operation
Continuous
Duration
1 second
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0722 (Output speed sensor circuit)
P0500 (Vehicle speed sensor circuit)
P2759 (Torque converter clutch pressure control solenoid circuit)
P2716 (Pressure control solenoid (SLT) circuit)
Transmission range
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT (Engine Coolant Temperature)
40°C (104°F) or more
Spark advance from max. retard timing by knock control
0°CA or more
L4 switch
OFF
Transfer range
"HIGH"
Engine
Starting
ATF (Automatic Transmission Fluid) temperature
-10°C (14°F) or more
ETCS (Electronic Throttle Control System)
Not system down

ON malfunction (A) 
ECM selected gear
1st, 2nd or 3rd
Input speed
300 rpm or more
Output speed
300 rpm or more

ON malfunction (B) 
ECM selected gear
4th

TYPICAL MALFUNCTION THRESHOLDS

Either of following conditions is met: ON malfunction (A) or (B)

ON malfunction (A) 
Duration
0.85 seconds or more
Input speed - Output speed x ECM selected gear ratio (1st to 3rd)
More than 350 rpm at output speed 1000 rpm
(Conditions vary with intermediate shaft speed)

ON malfunction (B) 
Duration
0.85 seconds or more
Input speed (4th)
300 rpm or more

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P2714 is output
    A
    P2714 and other DTCs are output
    B

    HINT:
    If any other codes besides P2714 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT SHIFT SOLENOID VALVE SLT


    C224013E01
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


4.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)