Home › TRANSMISSION ยท A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4bolts, then remove the engine under cover No.1.



3. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (for Regular Cab)
  1. Remove the 4 bolts, then remove engine cover No.2.



4. REMOVE FRONT FENDER SEAL LH


C226878
  1. Remove the 5 clips and front fender seal LH.



5. DISCONNECT WIRE HARNESS AND CONNECTOR


    C226966
  1. Disconnect the heated oxygen sensor connector and the heated oxygen sensor harness clamp.



    C226952
  1. Disconnect the air fuel ratio sensor connector and the air fuel ratio sensor harness clamp.



6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the exhaust pipe front from the exhaust pipe support.

  1. Remove the gasket from the exhaust manifold.



7. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


C098708E02
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



8. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



9. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Access Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



10. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug gasket, and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



11. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY


12. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


F050819
  1. Remove the 2 bolts and oil filler tube.



13. DISCONNECT NO. 1 OIL COOLER OUTLET TUBE


C227042
  1. Using a union nut wrench, disconnect the No. 1 oil cooler outlet tube.



14. DISCONNECT NO. 1 OIL COOLER INLET TUBE


C227724
  1. Remove the 3 bolts and 3 clamps.



    F050820
  1. Using a union nut wrench, disconnect the No. 1 oil cooler inlet tube.



15. REMOVE MANIFOLD STAY


F050821
  1. Remove the 3 bolts and manifold stay.



16. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


F050822
  1. Remove the nut and clip, and disconnect the transmission control cable assembly .



17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C226719
  1. Support the automatic transmission assembly with a transmission jack.



18. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    C226665
  1. Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.



    C226666
  1. Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.



19. REMOVE STARTER ASSEMBLY


G037949E01
  1. Remove the terminal cap.

  1. Remove the nut, then remove the starter wire harness.

  1. Disconnect the starter connector.



    G037950E01
  1. Remove the 2 bolts, then remove the starter.



20. DISCONNECT WIRE HARNESS AND CONNECTORS


C226720
  1. Tilt down the transmission.

    NOTICE:
    Take care so that the cooling fan does not come in contact with the fan shroud.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.

  1. Disconnect the temperature sensor connector.

  1. Disconnect the transfer control side connector.



  1. Detach the connector clamp and 7 harness clamps, and disconnect the wire harness.


    C226664



21. DISCONNECT TRANSFER BREATHER HOSE


C226900E01
  1. Disconnect the transfer breather hoses from the transfer breather bracket.



22. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
  1. Remove flywheel housing dust seal.



    G038108E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    F050825
  1. Remove the 6 torque converter setting bolts.



    C226881
  1. Remove the 8 bolts.

  1. Separate and remove the automatic transmission.



23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


24. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


G024484E01
  1. Remove the 2 bolts and the No. 1 transmission control cable bracket.



25. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C226667
  1. Remove the 4 bolts and the No. 1 engine mounting insulator rear.



26. REMOVE TRANSFER ASSEMBLY
(Click here)


27. INSPECT TORQUE CONVERTER


D029376E01


  1. Inspect the one-way clutch.

    1. Install SST into the inner race of the one-way clutch.

      SST
      09350-32014   (09351-32010)

    2. Set SST so that it fits in the notch of the converter hub and outer race of the one-way clutch.

      SST
      09350-32014   (09351-32020)



    3. D029377E04
    4. With the torque converter standing on its side, check that the clutch locks when turned counterclockwise and rotates freely and smoothly clockwise.
      If necessary, clean the converter and check the one-way clutch again.
      Replace the converter if the one-way clutch still does not operate as specified.
      Text in Illustration 
      V100135
      Lock
      V100136
      Free



    C197457E04
  1. Check the condition of the torque converter clutch assembly.
    Text in Illustration 
    *a
    Sample showing maximum allowable amount of powder in ATF

    1. If the inspection result of the torque converter clutch assembly matches any of the cases mentioned below, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in N.
      One-way clutch is free or locked in both directions. Fine powder exceeding the sample limit are identified in ATF. (See the sample.)

      HINT:
      The sample shows the auto fluid of approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation surface facing up.



    C011090
  1. Clean and then check the oil cooler and oil pipe line.

    1. If inspecting the torque converter clutch or exchanging the ATF, clean the oil cooler and oil pipe line.

      HINT:
      1. Apply compressed air of 196 kPa (2 kgf/cm2, 28 psi) from the inlet hose.
      2. If excessive fine powder is found in the ATF, add new ATF using a bucket pump and clean the ATF again.

    2. If the ATF is cloudy, inspect the oil cooler (radiator).



    D025368E29
  1. Be careful not to deform the torque converter clutch or damage the oil pump gear.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect
    *c
    Bottom is damaged

    1. When any marks due to interference are found on the end of the bolt on the torque converter clutch and on the bottom of the bolt hole, replace the bolt and the torque converter clutch.

    2. All the bolts should be the same length.

    3. Do not lose any spring washers.



28. INSPECT DRIVE PLATE AND RING GEAR
  1. Check the drive plate for damage.



    C191483E04
  1. Set up a dial indicator and measure the runout of the 6 portions around the torque converter fitting surfaces.

    Maximum runout:
    0.30 mm (0.0118 in.)

    Text in Illustration 
    *a
    Measuring point
    1. If the runout is more than the maximum or if the drive plate is damaged, replace the drive plate.