Home › TRANSMISSION · A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2757    Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)

for Preparation Click here


DESCRIPTION

The ECM uses the signals from the throttle position sensor, mass air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor, to monitor the engagement condition of the lock-up clutch.

C243320E01

Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect any mechanical problems with the shift solenoid valve SLU, valve body or torque converter.

DTC No.
DTC Detection Condition
Trouble Area
P2757
Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range. (2 trip detection logic)
  1. Shift solenoid valve SLU remains open or closed
  2. Valve body is blocked
  3. Shift solenoid valve SLU
  4. Torque converter assembly
  5. Automatic transmission (clutch, brake, gear, etc.)
  6. Line pressure is too low

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the turbine (input) speed sensor NCO, output speed sensor SP2, engine speed, engine load, engine coolant temperature, vehicle speed, transmission fluid temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) with the input turbine speed (NCO). The ECM calculates the actual transmission gear by comparing the input turbine speed (NCO) with the output shaft speed (SP2). When the conditions are appropriate, the ECM requests lock-up by applying the control voltage to the shift solenoid SLU. When the SLU is turned on, the solenoid SLU applies pressure to the lock-up relay valve and locks the torque converter.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in the shift solenoid valve SLU or lock-up system performance.
The ECM turns on the MIL and stores the DTC.
Example:
When any of the following are met, the ECM interprets it as a malfunction.
  1. (a) There is a difference in rotation between before and after the torque converter even when the ECM requests lock-up.
    (Engine speed is at least 70 rpm greater than the input turbine speed.)
  2. (b) There is no difference in rotation between before and after the torque converter even when the ECM requests lock-up off.
    (The difference between the engine speed and input turbine speed is less than 35 rpm.)

MONITOR STRATEGY


Related DTCs
P2757:
Shift solenoid valve SLU/OFF malfunction
Shift solenoid valve SLU/ON malfunction
Required sensors/Components
Shift solenoid valve SLU
Frequency of operation
Continuous
Duration
OFF malfunction (A):
2 seconds
OFF malfunction (B):
1 second
ON malfunction (A) and (B):
1.8 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0722 (Output speed sensor circuit)
P0500 (Vehicle speed sensor circuit)
P2759 (Torque converter clutch pressure control solenoid circuit)
Transmission shift position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT (Engine Coolant Temperature)
40°C (104°F) or more
Spark advance from max. retard timing by knock control
0°CA or more
L4 switch
OFF
Transfer range
"HIGH"
Engine
Starting
ECM selected gear
3rd or 4th
Vehicle speed
25 km/h (15.5 mph) or more

OFF malfunction (A) 
ECM lock-up command
ON
(SLU pressure: 90% or more)
Vehicle speed
Less than 100 km/h (62.1 mph)

OFF malfunction (B) 
ECM selected gear
2nd
Vehicle speed
10 km/h (6.2 mph) or more
Output speed
2nd → 1st down-shift point or more
Throttle valve opening angle
6.5% or more at 2000 rpm (Conditions vary with engine speed)

ON malfunction (A) and (B) 
ECM lock-up command
OFF
(SLU pressure: 10% or less)
Throttle valve opening angle
10 % or more
Vehicle speed
Less than 60 km/h (37.3 mph)

TYPICAL MALFUNCTION THRESHOLDS

OFF malfunction
  1. Both of the following conditions are met: OFF malfunction (A) and (B)

OFF malfunction (A) 
Engine speed - Output speed x 4th gear ratio
70 rpm or more

OFF malfunction (B) 
Input speed / Output speed
Less than 2.63, or more than 3.20
ON malfunction
  1. 2 detections are necessary in 1 driving cycle.
  2. 1st detection: Temporary flag ON
  3. 2nd detection: Pending fault code ON
  4. Vehicle speed must be under 10 km/h (6.2 mph) once before the 2nd detection.

ON malfunction (A) 
Engine speed - Input speed
Less than 35 rpm

ON malfunction (B) 
Engine speed - Output speed x 4th gear ratio
Less than 35 rpm

COMPONENT OPERATING RANGE


Speed sensor (NCO)
Input speed is equal to engine speed when lock-up is ON.

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Lock Up
    Control shift solenoid valve SLU to set automatic transmission to lock-up
    OFF or ON
    Possible to check shift solenoid valve SLU operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (36 mph) or more

    HINT:
    This test can be conducted when the vehicle speed is 60 km/h (36 mph) or more.



    C159073E03

    HINT:
    1. When changing the accelerator pedal opening angle while driving, if the engine speed does not change rapidly, lock-up is on.
    2. Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2757)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P2757 is output
    A
    P2757 and other DTCs are output
    B

    HINT:
    If any other codes besides P2757 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT SHIFT SOLENOID VALVE SLU


    C224014E01
  1. Remove shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.1 to 5.5 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLU)


NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on each valve.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


4.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)