Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P014C    A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1

DTC    P014D    A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1

DTC    P014E    A/F Sensor Slow Response - Rich to Lean Bank 2 Sensor 1

DTC    P014F    A/F Sensor Slow Response - Lean to Rich Bank 2 Sensor 1

DTC    P015A    A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1

DTC    P015B    A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1

DTC    P015C    A/F Sensor Delayed Response - Rich to Lean Bank 2 Sensor 1

DTC    P015D    A/F Sensor Delayed Response - Lean to Rich Bank 2 Sensor 1

for Preparation Click here


DESCRIPTION

HINT:
Refer to DTC P2195 .


DTC No.
DTC Detection Condition
Trouble Area
P014C
The "Rich to Lean response rate deterioration level*" value is standard or less(2 trip detection logic).
  1. Air fuel ratio sensor (bank 1 sensor 1)
  2. Air fuel ratio sensor (bank 1 sensor 1) heater
  3. ECM
P014D
The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
P015A
The "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
P015B
The "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
P014E
The "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
  1. Air fuel ratio sensor (bank 2 sensor 1)
  2. Air fuel ratio sensor (bank 2 sensor 1) heater
  3. ECM
P014F
The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
P015C
The "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
P015D
The "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
*: Calculated by the ECM based on the air fuel ratio sensor output

MONITOR DESCRIPTION

After the engine is warm, the ECM carries out air fuel ratio feedback control, and maintains the air fuel ratio at the stoichiometric level. In addition, after all the preconditions have been met, active air fuel ratio control is carried out for approximately. 10 seconds, and during active air fuel ratio control, the ECM measures the response of the air fuel ratio sensor by increasing or decreasing the injection volume by a specific quantity based on the stoichiometric air fuel ratio learned during normal air fuel control. The ECM determines whether there is an air fuel ratio sensor malfunction at the mid-point of active air fuel ratio control.
If the response of the air fuel ratio sensor is reduced, DTC P014C, P014D, P014E and P014F are stored.
If the time it takes the air fuel ratio sensor output to change is delayed, DTC P015A, P015B, P015C and P015D are stored.

A223538E24


MONITOR STRATEGY


Related DTCs
P014C: Air fuel ratio sensor (bank 1 sensor 1) slow response (rich to lean)
P014D: Air fuel ratio sensor (bank 1 sensor 1) slow response (lean to rich)
P014E: Air fuel ratio sensor (bank 2 sensor 1) slow response (rich to lean)
P014F: Air fuel ratio sensor (bank 2 sensor 1) slow response (lean to rich)
P015A: Air fuel ratio sensor (bank 1 sensor 1) delayed response (rich to lean)
P015B: Air fuel ratio sensor (bank 1 sensor 1) delayed response (lean to rich)
P015C: Air fuel ratio sensor (bank 2 sensor 1) delayed response (rich to lean)
P015D: Air fuel ratio sensor (bank 2 sensor 1) delayed response (lean to rich)
Required Sensors/Components (Main)
Air fuel ratio sensor (bank 1, 2 sensor 1)
Required Sensors/Components (Related)
Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
10 to 15 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
Active air fuel ratio control
Performing
Active air fuel ratio control is performed when the following conditions are met
-
Battery voltage
11 V or more
Engine coolant temperature
75°C (167°F) or higher
Idle
OFF
Engine speed
1000 rpm or higher, and less than 4000 rpm
Air fuel ratio sensor status
Activated
Fuel-cut
OFF
Engine load
10% or higher, and less than 70%
Shift position
2nd or higher
Catalyst monitor
Not yet
Mass air flow
6 gm/sec or more, and less than to 15 gm/sec.

TYPICAL MALFUNCTION THRESHOLDS


P014C and P014E: Air Fuel Ratio Sensor (Bank 1, 2) Response Rate (Rich to Lean Response Rate) 
Rich to Lean response rate deterioration level
0.04 V or less (Automatic Transmission)
0.036 V or less (Manual Transmission)

P014D and P014F: Air Fuel Ratio Sensor (Bank 1, 2) Response Rate (Lean to Rich Response Rate) 
Lean to Rich response rate deterioration level
-0.04 V or higher (Automatic Transmission)
-0.036 V or higher (Manual Transmission)

P015A and P015C: Air Fuel Ratio Sensor (Bank 1, 2) Response Rate (Rich to Lean Delay) 
Rich to Lean delay level
327.68 ms or more

P015B and P015D: Air Fuel Ratio Sensor (Bank 1, 2) Response Rate (Lean to Rich Delay) 
Lean to Rich delay level
327.68 ms or more

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A201252E02

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that the monitor item O2 Sensor is Incomplete.

    HINT:
    The test values for the test items RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1 do not exist in Details of the O2 Sensor monitor at this time (the initial value of "0.0000" or "0.000" is indicated for each test item).

  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  11. Check that the monitor item O2 Sensor becomes Complete.

    HINT:
    Check the test values on the Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1.

  12. If the monitor item O2 Sensor does not become Complete (if the test values indicated on the Techstream do not change), perform Readiness Monitor Drive Pattern for the air fuel ratio sensor and heated oxygen sensor (Click here).
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D.
  17. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.
  5. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  6. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  7. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output
    A
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D and other DTCs are output
    B

    HINT:
    If any DTCs other than P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A4-1 (HA1A) - E12-17 (HA1A)
    Always
    Below 1 Ω
    A4-3 (A1A+) - E11-1 (A1A+)
    Always
    Below 1 Ω
    A4-4 (A1A-) - E11-2 (A1A-)
    Always
    Below 1 Ω
    A5-1 (HA2A) - E12-19 (HA2A)
    Always
    Below 1 Ω
    A5-3 (A2A+) - E11-7 (A2A+)
    Always
    Below 1 Ω
    A5-4 (A2A-) - E11-8 (A2A-)
    Always
    Below 1 Ω
    A4-1 (HA1A) or E12-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    A4-3 (A1A+) or E11-1 (A1A+) - Body ground
    Always
    10 kΩ or higher
    A4-4 (A1A-) or E11-2 (A1A-) - Body ground
    Always
    10 kΩ or higher
    A5-1 (HA2A) or E12-19 (HA2A) - Body ground
    Always
    10 kΩ or higher
    A5-3 (A2A+) or E11-7 (A2A+) - Body ground
    Always
    10 kΩ or higher
    A5-4 (A2A-) or E11-8 (A2A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AIR FUEL RATIO SENSOR
  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


5.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


7.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


8.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


NEXT


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output
    B



B
CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
A

END