DTC B1800/51 Short in Driver Side Squib Circuit |
DTC B1801/51 Open in Driver Side Squib Circuit |
DTC B1802/51 Short to GND in Driver Side Squib Circuit |
DTC B1803/51 Short to B+ in Driver Side Squib Circuit |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1800/51 |
|
|
| B1801/51 |
|
|
| B1802/51 |
|
|
| B1803/51 |
|
|

| 1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
If using the Techstream (read the 5-digit DTCs):
Using the Techstream, check for DTCs (Click here).
| Result | Proceed to |
| DTC B1800 is output. | A |
| DTC B1801 is output. | B |
| DTC B1802 is output. | C |
| DTC B1803 is output. | D |
If not using the Techstream (read the 2-digit DTCs):
Check for DTCs (Click here).
| Result | Proceed to |
| DTC 51 is output. | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the center airbag sensor assembly and the spiral cable.
|
| ||||
| OK | |
| 4.CHECK SPIRAL CABLE (FOR SHORT) |
![]() |
Disconnect the spiral cable connectors from the instrument panel wire and steering pad.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D+ - D- | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 5.CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() |
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - A26-2 (D-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 6.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the instrument panel wire connectors to the center airbag sensor assembly and spiral cable.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | ||
| ||
| 7.CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
|
| ||||
| OK | |
| 8.CHECK CONNECTION OF CONNECTORS |
Check that the spiral cable connectors (on the steering pad side) are properly connected.
|
| ||||
| OK | |
| 9.CHECK SPIRAL CABLE (FOR OPEN) |
![]() |
Disconnect the spiral cable connectors from the instrument panel wire and steering pad.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D+ - D- | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - A26-2 (D-) | Always | Below 1 Ω |
|
| ||||
| NG | ||
| ||
| 11.CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
|
| ||||
| OK | |
| 12.CHECK CONNECTION OF CONNECTORS |
Check that the spiral cable connectors (on the steering pad side) are properly connected.
|
| ||||
| OK | |
| 13.CHECK SPIRAL CABLE (TO GROUND) |
![]() |
Disconnect the spiral cable connectors from the instrument panel wire and steering pad.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D+ - Body ground | Always | 1 MΩ or Higher |
| D- - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 14.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - Body ground | Always | 1 MΩ or Higher |
| A26-2 (D-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| NG | ||
| ||
| 15.CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
|
| ||||
| OK | |
| 16.CHECK CONNECTION OF CONNECTORS |
Check that the spiral cable connectors (on the steering pad side) are properly connected.
|
| ||||
| OK | |
| 17.CHECK SPIRAL CABLE (TO B+) |
![]() |
Disconnect the spiral cable connectors from the instrument panel wire and steering pad.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage
| Tester Connection | Condition | Specified Condition |
| D+ - Body ground | Ignition switch ON | Below 1 V |
| D- - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 18.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| A26-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 19.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the instrument panel wire connectors to the center airbag sensor assembly.
Using a service wire, connect D+ and D- of connector E.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 20.REPLACE STEERING PAD (DRIVE SIDE SQUIB) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the service wire from connector E.
Connect the connectors to the steering pad.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 21.CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
|
| ||||
| OK | |
| 22.CHECK CONNECTORS |
Check that the spiral cable connectors (on the steering pad side) are properly connected.
|
| ||||
| OK | |
| 23.CHECK SPIRAL CABLE |
![]() |
Disconnect the spiral cable connectors from the instrument panel wire and steering pad.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| D+ - Body ground | Ignition switch ON | Below 1 V |
| D- - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D+ - D- | Always | Below 1 Ω |
| D+ - Body ground | Always | 1 MΩ or Higher |
| D- - Body ground | Always | 1 MΩ or Higher |
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D+ - D- | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 24.CHECK INSTRUMENT PANEL WIRE |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| A26-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - A26-2 (D-) | Always | Below 1 Ω |
| A26-1 (D+) - Body ground | Always | 1 MΩ or Higher |
| A26-2 (D-) - Body ground | Always | 1 MΩ or Higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A26-1 (D+) - A26-2 (D-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 25.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Replace the steering pad (Click here).
Connect the instrument panel wire to the airbag sensor assembly center and spiral cable.
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||