Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster)

DTC    C146E    Open in ABS Solenoid Relay Circuit

DTC    C146F    Short in ABS Solenoid Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid and TRAC solenoid.
The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self diagnosis performed when the vehicle starts running.
The ABS solenoid relay is housed in the skid control ECU in the actuator assembly.

DTC Code
DTC Detection Condition
Trouble Area
C146E
When either of the following is detected:
  1. Both of the following conditions continue for 0.22 seconds or more.
    1. The IG1 terminal voltage is 9.5 V or more.
    2. The solenoid relay contact is open when the relay is ON.
  2. Both of the following conditions continue for 0.22 seconds or more.
    1. The IG1 terminal voltage becomes lower than 9.5 V or less when the relay is turned on.
    2. The relay contact remains open.
  1. ABS No. 2 fuse
  2. ABS solenoid relay circuit
  3. ABS solenoid relay (Brake actuator assembly)
C146F
Immediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4 seconds when the relay is turned off.
  1. ABS solenoid relay circuit
  2. ABS solenoid relay (Brake actuator assembly)

WIRING DIAGRAM

Refer to DTCs C1225, C1468, C1469, C146A and C146B .

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
When C1241 is output together with C146E and/or C146F inspect and repair the trouble areas indicated by C1241 first (Click here).

1.INSPECT ABS NO. 2 FUSE


    F051653E09
  1. Remove the ABS No. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ABS No. 2 fuse
    Always
    Below 1 Ω



NG
REPLACE ABS NO. 2 FUSE
OK


2.INSPECT SKID CONTROL ECU (+BS TERMINAL)


    C168924E11
  1. Install the ABS No. 2 fuse.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-12 (+BS) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK


3.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C168924E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4.RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The solenoid circuit is in the brake actuator assembly.
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Reconnect the skid control ECU (brake actuator assembly) connector.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
    4. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)