Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster)

DTC    C1425    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) inputs stop light switch signals and the brake operation condition.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open circuit in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code
DTC Detection Condition
Trouble Area
C1425
When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU (brake actuator assembly) STPO terminal output is off, an open in the stop light switch circuit (A to B, A to body ground) continues for 3 seconds or more.
  1. Stop light switch circuit
  2. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C248752E02


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform calibration (Click here).

1.CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Stop light switch function is normal.



NG
Go to step 5
OK


2.READ VALUE USING TECHSTREAM (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch/ ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light condition observed on the Techstream changes according to brake pedal operation.

Standard:
The Techstream displays ON or OFF according to brake pedal operation.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

3.INSPECT HARNESS AND CONNECTOR (STP TERMINAL)


    C220649E32
  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-2 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    S1-2 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
  1. Disconnect the stop light switch assembly connector.



    C204290E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S10-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Disconnect the stop light switch assembly connector.



    C124796E18
  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Switch Connection
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (to Stop Light Switch Assembly)
    *1
    Pushed in
    *2
    Free

  1. Reconnect the stop light switch assembly connector.
    Result 
    Result
    Proceed to
    NG
    A
    OK (w/o Trailer Towing)
    B
    OK (w/ Trailer Towing)
    C



B
Go to step 7

C
Go to step 8
A

REPLACE STOP LIGHT SWITCH ASSEMBLY 

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY, HIGH MOUNTED STOP LIGHT ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the skid control ECU connector.

  1. Disconnect the stop light switch connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Rear Combination Light Assembly RH 
    Tester Connection
    Condition
    Specified Condition
    R6-4 - S10-1
    Always
    Below 1 Ω
    R6-4 - Body ground
    Always
    10 kΩ or higher
    R6-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    Rear Combination Light Assembly LH 
    Tester Connection
    Condition
    Specified Condition
    R5-4 - S10-1
    Always
    Below 1 Ω
    R5-4 - Body ground
    Always
    10 kΩ or higher
    R5-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    High Mounted Stop Light Assembly 
    Tester Connection
    Condition
    Specified Condition
    C15-1 - S10-1
    Always
    Below 1 Ω
    C15-1 - Body ground
    Always
    10 kΩ or higher
    C15-2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the STOP LP CTRL relay.

  1. Reconnect the rear combination light assembly connector.

  1. Reconnect the high mounted stop light assembly connector.

Result 
Result
Proceed to
NG
A
OK (Rear Combination Light Assembly) (for Bulb Type Stop Light)
B
OK (Rear Combination Light Assembly) (for LED Type Stop Light)
C
OK (High Mounted Stop Light Assembly)
D


B
Go to step 11

C
Go to step 12

D
Go to step 13
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LP CTRL RELAY)
  1. Remove the STOP LP CTRL relay from the engine room relay block.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Connection
    Specified Condition
    S10-1 - STOP LP CTRL relay-4
    Always
    Below 1 Ω
    S10-1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the STOP LP CTRL relay from the engine room relay block.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT STOP LP CTRL RELAY


    E149024E04
  1. Remove the STOP LP CTRL relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage not applied
    Below 1 Ω
    Battery voltage applied to terminal 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    STOP LP CTRL Relay



NG
REPLACE STOP LP CTRL RELAY
OK


10.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY, HIGH MOUNTED STOP LIGHT ASSEMBLY - STOP LP CTRL RELAY)
  1. Disconnect the rear combination light assembly connector.

  1. Disconnect the high mounted stop light assembly connector.

  1. Remove the STOP LP CTRL relay.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Rear Combination Light Assembly RH 
    Tester Connection
    Condition
    Specified Condition
    R6-4 - STOP LP CTRL-3
    Always
    Below 1 Ω
    R6-4 - Body ground
    Always
    10 kΩ or higher
    R6-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    Rear Combination Light Assembly LH 
    Tester Connection
    Condition
    Specified Condition
    R5-4 - STOP LP CTRL-3
    Always
    Below 1 Ω
    R5-4 - Body ground
    Always
    10 kΩ or higher
    R5-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    High Mounted Stop Light Assembly 
    Tester Connection
    Condition
    Specified Condition
    C15-1 - STOP LP CTRL-3
    Always
    Below 1 Ω
    C15-1 - Body ground
    Always
    10 kΩ or higher
    C15-2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the STOP LP CTRL relay from the engine room relay block.

  1. Reconnect the rear combination light assembly connector.

  1. Reconnect the high mounted stop light assembly connector.
    Result 
    Result
    Proceed to
    NG
    A
    OK (Rear Combination Light Assembly) (for Bulb Type Stop Light)
    B
    OK (Rear Combination Light Assembly) (for LED Type Stop Light)
    C
    OK (High Mounted Stop Light Assembly)
    D



B
Go to step 11

C
Go to step 12

D
Go to step 13
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

11.INSPECT TAIL AND STOP LIGHT BULB
  1. Remove the rear combination light assembly connector .



    C248754E01
  1. Apply battery voltage to the terminals and check that the rear combination light illuminates.
    OK 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 4
    Negative battery - Terminal 3
    Rear combination light illuminates
    Text in Illustration 
    *a
    Component without harness connected
    (to Rear Combination Light Sssembly)

  1. Reinstall the rear combination light assembly.



NG
REPLACE TAIL AND STOP LIGHT BULB
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

12.INSPECT REAR COMBINATION LIGHT ASSEMBLY
  1. Remove the rear combination light assembly connector .



    C248754E01
  1. Apply battery voltage to the terminals and check that the rear combination light illuminates.
    OK 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 4
    Negative battery - Terminal 3
    Rear combination light illuminates
    Text in Illustration 
    *a
    Component without harness connected
    (to Rear Combination Light Sssembly)

  1. Reinstall the rear combination light assembly.



NG
REPLACE REAR COMBINATION LIGHT ASSEMBLY
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

13.INSPECT CENTER STOP LIGHT BULB
  1. Remove the high mounted stop light assembly connector.



    C248753E01
  1. Apply battery voltage to the terminals and check that the rear combination light illuminates.
    OK 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    High mounted stop light illuminates
    Text in Illustration 
    *a
    Component without harness connected
    (to High Mounted Stop Light Assembly)

  1. Reinstall the high mounted stop light assembly.



NG
REPLACE CENTER STOP LIGHT BULB
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)