Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster)

DTC    C1427    Motor Malfunction

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
C1427
Actuator pump motor does not operate properly.
  1. Brake actuator assembly (Ground circuit)
  2. Brake actuator assembly (Motor circuit)

WIRING DIAGRAM

Refer to DTCs C01361 and C146D .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/ TRAC / Active Test.

  1. Select the Active Test on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Relay ON/OFF
    Operating sound of motor can be heard

  1. Check for operating sound of the ABS motor relay when operating it using the Techstream.
    Result 
    Result
    Proceed to
    Operating sound is not heard
    A
    Operating sound is heard
    B



B
Go to step 3
A


2.INSPECT SKID CONTROL ECU (GND2 TERMINAL)


    C220649E35
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-13 (GND2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK


3.RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The ABS motor relay is in the brake actuator assembly.
Therefore, ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU (brake actuator assembly) connector.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC C1427 is not output
    A
    DTC C1427 is output
    B

    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
    4. The DTCs were possibly output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)