Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while engine is running
(2 trip detection logic)
  1. Open in air fuel ratio sensor (bank 1 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. ECM
P2238
When one of following conditions met.
(2 trip detection logic)
  1. Air fuel ratio sensor admittance: Less than 0.0074 1/Ω
  1. Voltage at terminal A1A+ is 0.5 V or less.
  1. Voltage difference between terminals A1A+ and A1A- is 0.1 V or less.
  1. Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. ECM
P2239
A1A+ voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. ECM
P2240
Open in the circuit between terminals A2A+ and A2A- of the A/F sensor while engine is running
(2 trip detection logic)
  1. Open in air fuel ratio sensor (bank 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. ECM
P2241
When one of following conditions met.
(2 trip detection logic)
  1. Air fuel ratio sensor admittance: Less than 0.0074 1/Ω
  1. Voltage at terminal A2A+ is 0.5 V or less.
  1. Voltage difference between terminals A2A+ and A2A- is 0.1 V or less.
  1. Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. ECM
P2242
A2A+ voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. ECM
P2252
A1A- voltage 0.5 V or less
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. ECM
P2253
A1A- voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. ECM
P2255
A2A- voltage 0.5 V or less
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. ECM
P2256
A2A- voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to the on position, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in next driving cycle, the MIL will be illuminated and a DTC will be stored.

MONITOR STRATEGY


Related DTCs
P2237: Air fuel ratio sensor (bank 1 sensor 1) open circuit between A1A+ and A1A-
P2238: Air fuel ratio sensor (bank 1 sensor 1) short circuit between A1A+ and A1A-
P2238: Air fuel ratio sensor (bank 1 sensor 1) short circuit between A1A+ and GND
P2238: Air fuel ratio sensor (bank 1 sensor 1) low impedance
P2239: Air fuel ratio sensor (bank 1 sensor 1) short circuit between A1A+ and +B
P2240: Air fuel ratio sensor (bank 2 sensor 1) open circuit between A2A+ and A2A-
P2241: Air fuel ratio sensor (bank 2 sensor 1) short circuit between A2A+ and A2A-
P2241: Air fuel ratio sensor (bank 2 sensor 1) short circuit between A2A+ and GND
P2241: Air fuel ratio sensor (bank 2 sensor 1) low impedance
P2242: Air fuel ratio sensor (bank 2 sensor 1) short circuit between A2A+ and +B
P2252: Air fuel ratio sensor (bank 1 sensor 1) short circuit between A1A- and GND
P2253: Air fuel ratio sensor (bank 1 sensor 1) short circuit between A1A- and +B
P2255: Air fuel ratio sensor (bank 2 sensor 1) short circuit between A2A- and GND
P2256: Air fuel ratio sensor (bank 2 sensor 1) short circuit between A2A- and +B
Required Sensors/Components (Main)
Air fuel ratio sensor (bank 1, 2 sensor 1)
Required Sensors/Components (Related)
Engine coolant temperature sensor
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
10 seconds: P2237 and P2240
10 seconds: P2238 and P2241 (air fuel ratio sensor low admittance)
5 seconds: Others
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2237, P2238, P2240 and P2241 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT system - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0412, P0418, P1613 (Secondary air injection system control)
P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary air injection system)
P0451, P0452, P0453 (EVAP system)
P0500, P0722 (Vehicle speed sensor)
P0505 (Idle speed control)
P219A, P219B (Air-fuel ratio imbalance)

P2239, P2242, P2252, P2253, P2255 and P2256 
Monitor runs whenever following DTCs not stored
None

P2237 and P2240: Air Fuel Ratio Sensor Open Circuit Between A1A+ and A1A-/A2A+ and A2A- 
Estimated sensor temperature
450 to 550°C (842 to 1022°F)
Engine
Running
Battery voltage
11 V or more
Ignition switch
ON
Time after ignition switch OFF to ON
5 seconds or more

P2238 and P2241: Air Fuel Ratio Sensor Low Impedance 
Estimated sensor temperature
700 to 800°C (1292 to 1472°F)
Engine coolant temperature
5°C (41°F) or higher
Fuel cut
Not executed

Other 
Battery voltage
11 V or more
Ignition switch
ON
Time after ignition switch OFF to ON
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 and P2240: Air Fuel Ratio Sensor Open Circuit Between A1A+ and A1A-/A2A+ and A2A- 
Air fuel ratio sensor admittance
Below 0.002 1/Ω

P2238 and P2241: Air Fuel Ratio Sensor Low Impedance 
Air fuel ratio sensor admittance
Below 0.0074 1/Ω

P2238 and P2241: Air Fuel Ratio Sensor Short Circuit Between A1A+ and GND/A2A+ and GND 
A1A+/A2A+ terminal voltage
0.5 V or less

P2239 and P2242: Air Fuel Ratio Sensor Short Circuit Between A1A+ and +B/A2A+ and +B 
A1A+/A2A+ terminal voltage
More than 4.5 V

P2252 and P2255: Air Fuel Ratio Sensor Short Circuit Between A1A- and GND/A2A- and GND 
A1A-/A2A- terminal voltage
0.5 V or less

P2253 and P2256: Air Fuel Ratio Sensor Short Circuit Between A1A- and +B/A2A- and +B 
A1A-/A2A- terminal voltage
More than 4.5 V

P2238 and P2241: Air Fuel Ratio Sensor Short Circuit Between A1A+ and A1A-/A2A+ and A2A- 
Difference between A1A+ terminal and A1A-/A2A+ terminal and A2A- terminal voltage
0.1 V or less

COMPONENT OPERATING RANGE


Air fuel ratio sensor admittance
0.022 1/Ω or more
A1A+/A2A+ terminal voltage
0.6 to 4.5 V
A1A-/A2A- terminal voltage
0.6 to 4.5 V
Difference between A1A+ and A1A-/A2A+ and A2A- terminal voltages
0.1 to 0.8 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and wait 5 minutes.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  6. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  7. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A4-1 (HA1A) - E12-17 (HA1A)
    Always
    Below 1 Ω
    A4-3 (A1A+) - E11-1 (A1A+)
    Always
    Below 1 Ω
    A4-4 (A1A-) - E11-2 (A1A-)
    Always
    Below 1 Ω
    A5-1 (HA2A) - E12-19 (HA2A)
    Always
    Below 1 Ω
    A5-3 (A2A+) - E11-7 (A2A+)
    Always
    Below 1 Ω
    A5-4 (A2A-) - E11-8 (A2A-)
    Always
    Below 1 Ω
    A4-1 (HA1A) or E12-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    A4-3 (A1A+) or E11-1 (A1A+) - Body ground
    Always
    10 kΩ or higher
    A4-4 (A1A-) or E11-2 (A1A-) - Body ground
    Always
    10 kΩ or higher
    A5-1 (HA2A) or E12-19 (HA2A) - Body ground
    Always
    10 kΩ or higher
    A5-3 (A2A+) or E11-7 (A2A+) - Body ground
    Always
    10 kΩ or higher
    A5-4 (A2A-) or E11-8 (A2A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.

  1. Check the DTC judgment.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output)
    B



B
REPLACE ECM (Click here)
A

END