Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

  1. Refer to DTC P0115 .

DTC No.
DTC Detection Condition
Trouble Area
P0116
When either of following conditions are met (2 trip detection logic):
  1. When cold engine started and engine warmed up, engine coolant temperature sensor value does not change.
  2. After warmed up engine stopped and then next cold engine start performed, engine coolant temperature sensor value does not change.
  1. Thermostat
  2. Engine coolant temperature sensor

MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Cold Start Monitor
  1. When a cold engine start is performed and then the engine is warmed-up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
Engine Coolant Temperature Sensor Soak Monitor
  1. If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY


Related DTCs
P0116: Engine Coolant Temperature Sensor Cold Start Monitor
P0116: Engine Coolant Temperature Sensor Soak Monitor
Required Sensors/Components (Main)
Engine coolant temperature sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Intake air temperature sensor
Mass air flow meter
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

Engine Coolant Temperature Sensor Cold Start Monitor 
Battery voltage
10.5 V or more
Time after engine start
1 second or more
Engine coolant temperature at engine start
Less than 60°C (140°F)
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125)
Not detected
Intake air temperature sensor circuit fail (P0112, P0113)
Not detected
Thermostat fail (P0128)
Not detected
Soak time
0 seconds or more
Accumulated mass air flow
1048 g or more
Fuel cut
OFF
Difference between engine coolant temperature at engine start and intake air temperature
Less than 40°C (72°F)

Engine Coolant Temperature Sensor Soak Monitor 
Battery voltage
10.5 V or higher
Engine
Running
Soak time
5 hours or more
Either condition (a) or (b) met
-
(a) Engine coolant temperature
60°C (140°F) or higher
(b) Accumulated mass air flow
2036 g or more
Intake air temperature sensor circuit fail (P0112, P0113)
Not detected
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125)
Not detected
Thermostat fail (P0128)
Not detected
Soak timer circuit fail (P2610)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Engine Coolant Temperature Sensor Cold Start Monitor 
Engine coolant temperature sensor value change
Less than 5°C (9°F)

Engine Coolant Temperature Sensor Soak Monitor 
Difference between current engine coolant temperature sensor value and previous engine coolant temperature sensor value when engine stopped
Less than 5°C (9°F) [varies with engine coolant temperature of last trip engine stop]

COMPONENT OPERATING RANGE


Engine coolant temperature
Engine coolant temperature sensor value changes in accordance with actual engine coolant temperature

CONFIRMATION DRIVING PATTERN


A198823E18

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
  4. Check that the engine coolant temperature is 60°C (140°F) or less.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Turn the ignition switch to ON and turn the Techstream on [A].
  8. Start the engine and idle it for 5 minutes or more [B].

    HINT:
    If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0116.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].

  14. Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.

  15. Check the DTC judgment result again [E].

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.

  16. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0115 .

INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0117, P0118 or P0125 are stored simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. When the DTC is output, check the engine coolant temperature using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0116 is output
    A
    P0116 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0116 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THERMOSTAT
  1. Check the valve opening temperature of the thermostat .



NG
REPLACE THERMOSTAT (Click here)
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR