Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1610/13    Front Airbag Sensor RH Circuit Malfunction

DTC    B1615/14    Front Airbag Sensor LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front airbag sensor RH consists of parts such as the diagnostic circuit and the frontal detection sensor.
The configuration of the front airbag sensor LH is the same as that of the RH.
When the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1610/13 is set when a malfunction is detected in the front airbag sensor RH circuit.
DTC B1615/14 is set when a malfunction is detected in the front airbag sensor LH circuit.

DTC No.
DTC Detecting Condition
Trouble Areas
B1610/13
  1. The center airbag sensor assembly receives a line short signal, an open signal, a short to ground signal or a short to B+ signal in the front airbag sensor RH circuit for 2 seconds
  2. Front airbag sensor RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Front airbag sensor RH
  2. Center airbag sensor assembly
  3. Instrument panel wire
  4. Engine room main wire
B1615/14
  1. The center airbag sensor assembly receives a line short signal, an open signal, a short to ground signal or a short to B+ signal in the front airbag sensor LH circuit for 2 seconds
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Front airbag sensor LH
  2. Center airbag sensor assembly
  3. Instrument panel wire
  4. Engine room main wire

WIRING DIAGRAM


H101959E02


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat outer belt assembly LH.
  7. (g) Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  8. (h) Disconnect the connector from the front seat airbag assembly LH.
  9. (i) Disconnect the connector from the front seat airbag assembly RH.
  10. (j) Disconnect the connector from the curtain shield airbag assembly LH.
  11. (k) Disconnect the connector from the curtain shield airbag assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. Check the DTC (Click here).

      Result:
      Result
      Proceed to
      DTC B1610/13 is output.
      A
      DTC B1615/14 is output.
      B
      DTC B1610/13 and B1615/14 are output.
      C
      Neither DTC B1610/13 nor B1615/14 is output.
      D



B
Go to step 14

C
Go to step 26

D
USE SIMULATION METHOD TO CHECK
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the airbag sensor front RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTOR
  1. Check that the connectors (on the center airbag sensor assembly side and airbag sensor front RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR OPEN)


    H100831E03
  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.

  1. Using a service wire, connect A12-2 (+SR) and A12-1 (-SR) of connector E.

    NOTICE:
    Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    A21-29 (+SR) - A21-27 (-SR)
    Always
    Below 1 Ω



NG
Go to step 10
OK


5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR SHORT)


    H100832E03
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    A21-29 (+SR) - A21-27 (-SR)
    Always
    1 MΩ or higher



NG
Go to step 11
OK


6.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+)


    H100832E03
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester connection
    Condition
    Specified Condition
    A21-29 (+SR) - Body ground
    Ignition switch ON
    Below 1 V
    A21-27 (-SR) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 12
OK


7.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND)


    H100832E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

Standard resistance:
Tester connection
Condition
Specified Condition
A21-29 (+SR) - Body ground
Always
1 MΩ or higher
A21-27 (-SR) - Body ground
Always
1 MΩ or higher



NG
Go to step 13
OK


8.CHECK FRONT AIRBAG SENSOR RH


    H100833E03
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the airbag sensor front RH with the front airbag sensor LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

Result:
Result
Proceed to
DTC B1610/13 is output.
A
DTC B1615/14 is output.
B
Neither DTC B1610/13 nor B1615/14 is output.
C



B
REPLACE FRONT AIRBAG SENSOR RH

C
USE SIMULATION METHOD TO CHECK
A


9.REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    H100830E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1610/13 is not output.

HINT:
DTCs other than B1610/13 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT AIRBAG SENSOR RH
OK

END 

10.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN)


    H100834E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

HINT:
The service wire has already been inserted into connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2 -1 (-SR) - IA2-2 (+SR)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

11.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT)


    H100835E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2 -1 (-SR) - IA2-2 (+SR)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

12.CHECK ENGINE ROOM MAIN WIRE (TO B+)


    H100835E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IA2 -1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V
    IA2-2 (+SR) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

13.CHECK ENGINE ROOM MAIN WIRE (TO GROUND)


    H100835E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2 -1 (-SR) - Body ground
    Always
    1 MΩ or higher
    IA2-2 (+SR) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

14.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


15.CHECK CONNECTOR
  1. Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


16.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR OPEN)


    H100831E14
  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH.

  1. Using a service wire, connect A11-2 (+SL) and A11-1 (-SL) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21 -30 (+SL) - A21-28 (-SL)
    Always
    Below 1 Ω



NG
Go to step 22
OK


17.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR SHORT)


    H100832E07
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21 -30 (+SL) - A21-28 (-SL)
    Always
    1 MΩ or Higher



NG
Go to step 23
OK


18.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+)


    H100832E07
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21 -30 (+SL) - Body ground
    Ignition switch ON
    Below 1V
    A21-28 (-SL) - Body ground
    Ignition switch ON
    Below 1V



NG
Go to step 24
OK


19.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND)


    H100832E07
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21 -30 (+SL) - Body ground
    Always
    1 MΩ or Higher
    A21-28 (-SL) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 25
OK


20.CHECK FRONT AIRBAG SENSOR LH


    H100833E05
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with the front airbag sensor LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1615/14 is output.
    A
    DTC B1610/13 is output.
    B
    Neither DTC B1610/13 nor B1615/14 is output.
    C



B
REPLACE FRONT AIRBAG SENSOR LH

C
USE SIMULATION METHOD TO CHECK
A


21.REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    H100836E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly .

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1615/14 is not output.

HINT:
DTCs other than B1615/14 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT AIRBAG SENSOR LH
OK

END 

22.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN)


    H100834E04
  1. Disconnect the engine room main wire connector from the instrument panel wire.

    HINT:
    The service wire has already been inserted into connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - IA2-4 (+SL)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

Go to step 44

23.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT)


    H100835E04
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - IA2-4 (+SL)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

Go to step 44

24.CHECK ENGINE ROOM MAIN WIRE (TO B+)


    H100835E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    IA2-4 (+SL) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

Go to step 44

25.CHECK ENGINE ROOM MAIN WIRE (TO GROUND)


    H100835E04
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - Body ground
    Always
    1 MΩ or Higher
    IA2-4 (+SL) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

Go to step 44

26.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly , the front airbag sensor LH and the front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


27.CHECK CONNECTOR
  1. Check that the connectors (on the center airbag sensor assembly side, front airbag sensor LH side and front airbag sensor RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


28.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR OPEN)


    H100831E03
  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.

  1. Using a service wire, connect A12-2 (+SR) and A12-1 (-SR) of connector E.

NOTICE:
Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-29 (+SR) - A21-27 (-SR)
    Always
    Below 1 Ω



NG
Go to step 32
OK


29.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR SHORT)


    H100832E03
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-29 (+SR) - A21-27 (-SR)
    Always
    1 MΩ or Higher



NG
Go to step 33
OK


30.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+)


    H100832E03
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-29 (+SR) - Body ground
    Ignition switch ON
    Below 1 V
    A21-27 (-SR) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 34
OK


31.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND)


    H100832E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-29 (+SR) - Body ground
    Always
    1 MΩ or Higher
    A21-27 (+SR) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 35

OK
Go to step 36

32.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN)


    H100834E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

HINT:
The service wire has already been inserted into connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-1 (-SR) - IA2-2 (+SR)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

33.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT)


    H100835E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-1 (-SR) - IA2-2 (+SR)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

34.CHECK ENGINE ROOM MAIN WIRE (TO B+)


    H100835E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IA2-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V
    IA2-2 (+SR) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

35.CHECK ENGINE ROOM MAIN WIRE (TO GROUND)


    H100835E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-1 (-SR) - Body ground
    Always
    1 MΩ or Higher
    IA2-2 (+SR) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

36.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR OPEN)


    H100831E06
  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH.

  1. Using a service wire, connect A11-2 (+SL) and A11-1 (-SL) of connector E.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-30 (+SR) - A21-28 (-SR)
    Always
    Below 1 Ω



NG
Go to step 40
OK


37.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR SHORT)


    H100832E07
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-30 (+SL) - A21-28 (-SL)
    Always
    1 MΩ or Higher



NG
Go to step 41
OK


38.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+)


    H100832E07
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-30 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    A21-28 (-SL) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 42
OK


39.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND)


    H100832E07
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-30 (+SL) - Body ground
    Always
    1 MΩ or Higher
    A21-28 (-SL) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 43

OK
Go to step 44

40.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN)


    H100834E04
  1. Disconnect the engine room main wire connector from the instrument panel wire.

    HINT:
    The service wire has already been inserted into connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - IA2-4 (+SL)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

41.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT)


    H100835E04
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - IA2-4 (+SL)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

42.CHECK ENGINE ROOM MAIN WIRE (TO B+)


    H100835E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    IA2-4 (+SL) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

43.CHECK ENGINE ROOM MAIN WIRE (TO GROUND)


    H100835E04
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IA2-3 (-SL) - Body ground
    Always
    1 MΩ or Higher
    IA2-4 (+SL) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

44.REPAIR OR REPLACE INSTRUMENT PANEL WIRE


    H046146E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly , front airbag sensor RH and front airbag sensor LH .

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1610/13 and B1615/14 are not output.

HINT:
DTCs other than B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT AIRBAG SENSOR RH AND LH
OK

END