Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2444    Secondary Air Injection System Pump Stuck On Bank1

DTC    P2445    Secondary Air Injection System Pump Stuck Off Bank1

for Preparation Click here


DESCRIPTION

Refer to P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2444
Secondary air pressure more than 2.5 kPa (18.751 mmHg) despite ECM commanding air pump to turn off (2 trip detection logic)
  1. Short in air pump circuit
  2. Open or short in air pressure sensor circuit
  3. Air pressure sensor
  4. Air injection control driver
  5. ECM
P2445
Secondary air pressure less than 2.5 kPa (18.751 mmHg) despite ECM commanding air pump to turn on (2 trip detection logic)
  1. Air pump assembly
  2. Open in air pump circuit
  3. Air injection system piping
  4. Vacuum hose (air pressure sensor - air switching valve)
  5. Air pressure sensor
  6. Open or short in air pressure sensor circuit
  7. Air injection control driver
  8. ECM

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the air pressure sensor located on the air switching valve assembly of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:
  1. The pressure indicated by the air pressure sensor does not reach threshold levels despite the ECM turning on the air pump assembly.
  2. The pressure indicated by the air pressure sensor exceeds threshold levels despite the ECM turning off the air pump assembly.

MONITOR STRATEGY


Related DTCs
P2444: Air Pump Stuck ON
P2445: Air Pump Stuck OFF
Required Sensors/Components (Main)
Air pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per drive cycle
Duration
7 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
P0010 (VVT Oil Control Valve)
P0011 (VVT System - Advance)
P0012 (VVT System - Retard)
P0016 (VVT System - Misalignment)
P0031, P0032 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air Fuel Ratio Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0171, P0172 (Fuel System)
P0301 - P0304 (Misfire)
P0327, P0328 (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0351 - P0354 (Igniter)
P0451, P0452, P0453 (EVAP System)
P0500, P0722 (Vehicle Speed Sensor)
P106B (EVAP Emission Control System Pressure Sensor - Air Injection System Pressure Sensor Correlation)
P2431, P2432, P2433 (Secondary Air Injection System)

Secondary Air Injection ON: 
Battery voltage
11 V or more
Atmospheric pressure
45 kPa(abs) [337.5 mmHg(abs)] or more
Pressure pattern check during secondary air injection ON*1
Completed
Pressure pattern check during secondary air injection OFF*2
Completed
Air injection control driver failure (open/short or out of range)
Not detected
Secondary air injection system pressure sensor failure (open/short or out of range)
Not detected

*1: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
6 seconds or more
Air pump
ON
Air switching valve
Open
Engine speed
Less than 3750 rpm
Time after engine start
1 second or more

*2: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
10 seconds or more
Air pump
OFF
Engine speed
Less than 3750 rpm
Secondary air injection monitor during secondary air injection ON
Completed

Air Switching Valve is Stuck Open: 
Air injection pump
OFF
Engine speed
3750 rpm or less
Secondary air injection pressure sensor (open/short of out of range)
Not detected
Time after secondary air injection system in operation
10 seconds or more
Air switching valve open stuck (P2440, P2442)
ON
Secondary air injection pressure sensor open stuck (P2445)
Not detected
Engine load
7% or more

TYPICAL MALFUNCTION THRESHOLDS


Secondary Air Injection ON (Condition 1): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection ON (Condition 2): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

Secondary Air Injection ON (Condition 3): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection ON (Condition 4): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

Secondary Air Injection OFF (Condition 1): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection OFF (Condition 2): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

Secondary Air Injection OFF (Condition 3): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection OFF (Condition 4): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

P2444 Air Pump is Stuck ON 
One of the following conditions is met
(a) or (b)
(a) Condition 1 (secondary air injection OFF)
-
(b) Condition 3 (secondary air injection OFF)
-

P2445 Air Pump is Stuck ON 
One of the following conditions is met
(a) or (b)
(a) Condition 2 (secondary air injection OFF)
-
(b) Condition 4 (secondary air injection OFF)
-

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
    If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Check for pending DTCs.

    OK:
    No pending DTC is output.

  14. After the "Secondary Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2444 or P2445.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  18. Turn the ignition switch off.

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump assembly and air switching valve assembly and stores a DTC. Soon after cold engine starts, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 4 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.


Pressure condition in Secondary Air Injection System Case 1: 
Air Pump
ON
Air Switching Valve
Open
Pressure
2.5 kPa (18.751 mmHg) or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure condition in Secondary Air Injection System Case 2: 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 2.5 kPa (18.751 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure condition in Secondary Air Injection System Case 3: 
Air Pump
ON
Air Switching Valve
Closed
Pressure
2.5 kPa (18.751 mmHg) or more
Pulsation Detection
Slight pulsation detected

Pressure condition in Secondary Air Injection System Case 4: 
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 2.5 kPa (18.751 mmHg)
Pulsation Detection
Exhaust pulsation not detected
If the detected pressure is high, the air pump assembly is assumed to be ON and if it alternates sharply*, the air switching valve assembly is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.
*: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

HINT:
  1. In case 3, as the air pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the air switching valve assembly, the average pressure is higher than in case 1 [approximately 20 to 30 kPa (150.120 to 225.018 mmHg)].
  2. In case 1, the average pressure is approximately 9 to 11 kPa (67.505 to 82.506 mmHg). The value of 2.5 kPa (18.751 mmHg) indicated in the table above is a threshold for detecting pump malfunctions.


Detected Condition while secondary air injection Operating:
Air Pump ON, Air Switching Valve Open
Detected Condition while secondary air injection not Operating:
Air Pump OFF, Air Switching Valve Closed
ECM Determination
DTCs Output
Case 1
Case 4
Normal
-
Case 1
Case 2
Air switching valve stuck open
P2440
Case 1
Case 3
Air pump stuck ON
P2444
Case 2
Case 4
Air pump stuck OFF
P2445
Case 3
Case 4
Air switching valve stuck closed
P2441
Case 1
Case 1
Air switching valve stuck open and Air pump stuck ON
P2440 and P2444
Case 2
Case 2
Air switching valve stuck open and Air pump stuck OFF
P2440 and P2445
Case 3
Case 3
Air switching valve stuck closed and Air pump stuck ON
P2441 and P2444
Case 4
Case 4
Air switching valve stuck closed and Air pump stuck OFF
P2441 and P2445

HINT:
  1. If the vacuum hose between the air switching valve assembly and the air pressure sensor is not connected correctly, case 4 may occur.
  2. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending DTCs also can be checked by performing System Check / Automatic Mode after the repair.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:
  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    7. Start the engine.
    8. Perform the secondary air injection system forced operation while the engine is idling.
    9. Check that the air pump assembly (AIR PUMP), air switching valve assembly (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream, indicate the conditions shown in the table below.

      Standard:

      Techstream Operation
      AIR PUMP
      ASV
      PRESSURE*1
      PULSATION*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      2.5 kPa (18.751 mmHg) or more
      11.25 kPa (84.381 mmHg) or more
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Less than 2.5 kPa (18.751 mmHg)
      Less than 11.25 kPa (84.381 mmHg)

      *1: Average pumping pressure (gauge pressure). The pressure should be 2.5 kPa (18.751 mmHg) or more when the secondary air injection system operates.
      *2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
    10. Turn the ignition switch off.

      NOTICE:
      1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
        Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 AND/OR P2445)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P2444 and/or P2445 is output
    A
    DTC P2444 and/or P2445, and P0418 are output
    B
    DTC P2444 and/or P2445, and other DTCs (except P0418) are output
    C
    If any DTCs other than P2444, P2445 and/or P0418 are output, troubleshoot those DTCs first.



B
GO TO AIR PUMP INSPECTION PROCEDURE

C
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.



    A065741E81
  1. Check that the air pump assembly (AIR PUMP), air switching valve assembly (ASV) and pressure in the secondary air injection system passage (PRESSURE) status displayed on the Techstream, indicate the conditions shown in the table below.
    Text in Illustration 
    *a
    Component with wire harness connected
    (ECM)

    HINT:
    At the same time, also measure the voltage according to the value(s) in the table below.


    Standard:

    Techstream Operation
    Air Pump
    Air Switching Valve
    PRESSURE*
    Tester Connection
    Specified Condition
    AIR PUMP: ON, ASV: OPEN
    ON
    ON
    2.5 kPa (18.751 mmHg) or more
    E4-11 (AIRP) - E4-3 (E1)
    3.5 to 7.5 V
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    OFF
    Less than 2.5 kPa (18.751 mmHg)
    E4-11 (AIRP) - E4-3 (E1)
    10 V or more

    *: Average pumping pressure. The pressure should be 2.5 kPa (18.751 mmHg) or more when the secondary air injection system operates.

  1. Turn the ignition switch off.

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
      If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

    Result 
    Result
    Proceed to
    DTC P2444 and/or P2445 is output
    A
    No pending DTC
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


4.CHECK VACUUM HOSES (AIR PRESSURE SENSOR - AIR SWITCHING VALVE ASSEMBLY)
  1. Check the vacuum hose connections with the air pressure sensor and air switching valve.

  1. Inspect the vacuum hose for blockages and damage.

    OK:
    Vacuum hose has no blockages or damage.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


5.INSPECT AIR PRESSURE SENSOR
G034995E03
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute).

  1. Check that the pressure displayed on the Techstream fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.
    Text in Illustration 
    *1
    Pressure Gauge
    *2
    Air Pressure Sensor

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The Techstream displays the air pump pressure (Air Pump Pressure (Absolute) as absolute pressure.



NG
REPLACE AIR PRESSURE SENSOR
OK


6.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

A121763E02


Text in Illustration 
*1
Air Pressure Sensor
*2
Air Switching Valve Assembly
*3
Air Pump Assembly
-
-
  1. Check that all the pipes and hoses between the air pump assembly and air switching valve assembly are securely connected.

  1. Inspect the pipes and hoses for blockages and damage.

    OK:
    Secondary air injection system piping has no blockages or damage.



NG
REPAIR OR REPLACE SECONDARY AIR INJECTION SYSTEM PIPING
OK


7.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A115629E05
  1. Disconnect the air injection control driver connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-5 (+B) - Body ground
    Ignition Switch ON
    11 to 14 V
    A6-1 (BATT) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A7-1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


8.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E4-11 (AIRP) - A7-4 (SIP)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A7-4 (SIP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT AIR PUMP ASSEMBLY
A222978E02
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the 400 A probe of an ammeter to the (+) wire of the air pump.
    Text in Illustration 
    *1
    Air Pump Wire
    *2
    Air Injection Control Driver

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Measure the current while the air pump is on and off.

    Standard Current:

    Techstream Operation
    Air Pump
    Air Switching Valve
    Specified Condition
    AIR PUMP: ON, ASV: OPEN
    ON
    OPEN
    10 to 40 A
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    CLOSE
    Below 1 A

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While secondary air injection system operation using the Techstream is prohibition (WAIT or ERROR).
      If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected. Wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 12
OK


10.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


NEXT

END 

12.REPLACE AIR PUMP ASSEMBLY
  1. Replace the air pump assembly (Click here).


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 14
OK

END 

14.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


NEXT

END