Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
These DTCs relate to the throttle position sensor.

The throttle position sensor is mounted on the throttle with motor body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A208679E41


DTC No.
DTC Detection Condition
Trouble Area
P0120
The output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. ECM
P0121
The difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds or less (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Throttle position sensor circuit
  3. ECM
P0122
The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
The output voltage of VTA1 is 4.54 V or more for 2 seconds or more (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
The output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. ECM
P0222
The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
The output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic)
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) is met (1 trip detection logic):
  1. (a) The difference between output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more
  2. (b) The output voltage of VTA1 is 0.2 V or less and VTA2 is 1.75 V or less for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. Throttle position sensor (built into throttle with motor body assembly)
  3. ECM

HINT:
  1. When any of these DTCs are output, check the throttle valve opening angle using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
  2. Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.


Reference (Normal Condition) 
Techstream Display
Accelerator Pedal Fully Released
Accelerator Pedal Fully Depressed
Throttle Position No. 1
0.5 to 1.1 V
3.2 to 4.8 V
Throttle Position No. 2
2.1 to 3.1 V
4.6 to 5.0 V

MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
P0120, P0122, P0123, P0220, P0223 and P2135:
  1. A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and stores a DTC.
  2. VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and stores a DTC.
  3. VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.
P0121:
  1. This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.
    For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the throttle position sensor. The ECM illuminates the MIL and stores the DTC.
    If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0120: Throttle position sensor 1 range check (Fluctuating)
P0121: Throttle position sensor rationality
P0122: Throttle position sensor 1 range check (Low voltage)
P0123: Throttle position sensor 1 range check (High voltage)
P0220: Throttle position sensor 2 range check (Fluctuating)
P0222: Throttle position sensor 2 range check (Low voltage)
P0223: Throttle position sensor 2 range check (High voltage)
P2135: Throttle position sensor range check (Correlation)
Required Sensors/Components (Main)
Throttle position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223
Within 2 seconds: P0121
0.5 seconds: P2135 (Case 1)
0.4 seconds: P2135 (Case 2)
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
None

P0120, P0122, P0123, P0220, P0222, P0223 and P2135 
Either of following conditions A or B met
-
A. Ignition switch ON
0.012 seconds or more
B. Electronic throttle actuator power
ON

P0121 
Either of following conditions A or B met
-
A. Ignition switch
ON
B. Electronic throttle motor power
ON
Throttle position sensor malfunction (P0120, P0122, P0123, P0220, P0222, P0223, P2135)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P0120 
VTA1 voltage
0.2 V or less, or 4.54 V or more

P0121 
Either of following conditions is met
-
Difference of learned throttle position sensor opener position voltage between VTA1 and VTA2 x 0.8
More than 1.6 V
Difference of learned throttle position sensor opener position voltage between VTA1 and VTA2 x 0.8
Less than 0.8 V

P0122 
VTA1 voltage
0.2 V or less

P0123 
VTA1 voltage
4.54 V or more

P0220 
When either condition below is met:
Condition A or B
A. VTA2 voltage
1.75 V or less
B. VTA2 voltage when VTA1 0.2 V or more, and 2.02 V or less
4.8 V or more

P0222 
VTA2 voltage
1.75 V or less

P0223 
VTA2 voltage when VTA1 0.2 V or more, and 2.02 V or less
4.8 V or more

P2135 Case 1 
Difference between VTA1 and VTA2 voltages
0.02 V or less

P2135 Case 2 
VTA1 voltage
0.2 V or less
VTA2 voltage
1.75 V or less

COMPONENT OPERATING RANGE


VTA1 voltage
0.69 to 4.05 V
VTA2 voltage
2.25 to 4.8 V

CONFIRMATION DRIVING PATTERN


A198824E10

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. With the vehicle stationary, fully depress and release the accelerator pedal [B].
  8. Idle the engine for 2 seconds or more [C].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [D] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When any of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A148768E45


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (THROTTLE POSITION SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

  1. Check the values displayed on the Techstream.
    Read the values.

    Result 
    When Accelerator Pedal Released
    When Accelerator Pedal Depressed
    Trouble Area
    Proceed to
    Throttle Position No. 1
    Throttle Position No. 2
    Throttle Position No. 1
    Throttle Position No. 2
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    VC circuit open
    A
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    E2 circuit open
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    2.1 V to 3.1 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    2.1 V to 3.1 V
    (Fail-safe)
    VTA1 circuit open
    or ground short
    0.6 V to 1.4 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    0.6 V to 1.4 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    VTA2 circuit open
    or ground short
    0.5 V to 1.1 V
    2.1 V to 3.1 V
    3.2 V to 4.8 V
    (Not fail-safe)
    4.6 V to 5.0 V
    (Not fail-safe)
    Throttle position sensor circuit normal
    B

    HINT:
    1. DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

      Characteristic Sensor Output:
      VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
      VTA1: Throttle Position No. 1
      VTA2: Throttle Position No. 2

    2. If DTC P0121 is output, proceed to "Check Harness and Connector (Throttle Position Sensor - ECM)".



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
  1. Disconnect the throttle with motor body assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    T1-5 (VC) - E11-13 (VCTA)
    Always
    Below 1 Ω
    T1-6 (VTA) - E11-15 (VTA1)
    Always
    Below 1 Ω
    T1-4 (VTA2) - E11-16 (VTA2)
    Always
    Below 1 Ω
    T1-3 (E2) - E11-14 (ETA)
    Always
    Below 1 Ω
    T1-5 (VC) or E11-13 (VCTA) - Body ground
    Always
    10 kΩ or higher
    T1-6 (VTA) or E11-15 (VTA1) - Body ground
    Always
    10 kΩ or higher
    T1-4 (VTA2) or E11-16 (VTA2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VC VOLTAGE)
A199036E22
  1. Disconnect the throttle with motor body assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T1-5 (VC) - T1-3 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Throttle with Motor Body Assembly)



NG
REPLACE ECM (Click here)
OK


4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Replace the throttle with motor body assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135 are output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)